Hi,
I had trouble with CTS serial port squelch (on microHAM USB Interface III).
It seems there is a bug in the hamlib code and I think the similar thing
should be done as has been done for the pttport, i.e. if the dcdport is
the same as the rigport, do not reopen it. Otherwise the serial port will
be reset to its default and it will key the radio PTT forever (because
the RTS line is reset on the port reopen). Patch attached
73! Jaroslav, OK2JRQ
Hi,
on 64 bit distros with /usr/lib64 (e.g Fedora) the hardcoded libdir in
pcconfig is wrong. The attached patch tries to fix it. It also applies
to 3.1
73! Jaroslav, OK2JRQ
Expand variable substituion for hamlib.pc
Further testing showed that 'exec_prefix' and 'includedir' would benefit from
variable substitution by the configure script.
- N0NB
This flag can be used by back ends that need to take special action
while the rig is transmitting e.g. the FT-747GX and similar that do
not process CAT commands while transmitting.
The flag is also used as a default answer to rig_get_ptt if nothing
better is available.
Deal with inaccurate CAT query for Rx/Tx on the Yaesu FT-847
This rig doesn't set the Rx/Tx status flag when PTT is asserted via
the PTT pin on the rear PACKET socket so we need to override which we
can do if we known we have asserted PTT via rig_set_ptt().
Adjust style and fix set PTT defects
Fix a warning from a declaration of a deleted function definition
Various SDR consoles are supported by the TS-2000 back end, ensure
that commands unsupported are not sent to them. Added a flag that
shows back end is talking to an emulation like SmartSDR or PowerSDR.
Found that when nothing was installed that check-tcl failed with a
failure of tclsh not being able to load the shared library. Thanks to
assistance from comp.lang.tcl, copying pkgIndex.tcl to $(builddir)/.libs
prior to loading the test script allows the script to load the shared
library immediately after 'make' and before 'make install'.
Prefixed various TCL section target commands with either $(AM_V_GEN) or
$(AM_V_at) to conditionally silence the output of 'make'.
Remove execute bits for all test scripts and install them into
doc/examples.
Make sure check-py and check-tcl targets work.
Set a conditional for Python3 or Python2 and install/test the correct
script file.
Use Makefile variables instead of configure substitutions wherever
possible.
Generate tcltest.tcl at make time to insert installation library path
into the script so that tests pass.
Also reorder its call in configure.ac which now allows the PYTHON_VERSION
environment variable to be recognized and processed correctly by the
build system.
Correctly add PYTHON_LIBS (correct ouput variable of AX_PYTHON_DEVEL) to the
Makefile for the Python bindings.
Update README.python for use of PYTHON_VERSION.
The increasing popularity of Python3 requires that Hamlib provide a
means of instruction for building and installing its module concurrent
with the Python2 module. README.python outlines the required steps.
py3test.py is a reworking of the pytest.py script for Python3 syntax.
on the real rig. In rigctl_parse.c, we make sure that invalid attempts to
so so are mapped on a safe variant.
Second change to netrigctl: drain the input line before sending a new
command, to reach sync again after a timeout.
Separate FT-891 features
Fix rigctl and rigctld to not abort on function not available
Change Yaesu detection of FA length to automatic method instead of rig specific
Although there is no reasonable recovery from SIGPIPE we do not want
to terminate the server process, just the client servicing thread. We
do this by setting the disposition for SIGPIPE to ignored, this causes
an EPIPE to be returned from blocked write() and send() calls that end
up trying to send to a broken pipe/socket.
Add driver for SPID MD-01 and MD-02 in ROT2 mode. The MD-01 and MD-02
extend the command set from the original ROT2PROG and deviate slightly
from the original protocol on the set_position command.
