librenms/doc/INSTALL_RHEL.md

NOTE: What follows is a very rough list of commands. This works on a fresh install of CentOS 6.4.

NOTE: These instructions assume you are the root user. If you are not, prepend sudo to all shell commands (the ones that aren't at mysql> prompts) or temporarily become a user with root privileges with sudo -s.

On the DB Server

yum install net-snmp mysql-server
service snmpd start
service mysqld start
chkconfig --levels 235 mysqld on
chkconfig --levels 235 snmpd on
mysql_secure_installation
mysql -uroot -p

Enter the MySQL root password to enter the MySQL command-line interface.

Create database.

CREATE DATABASE librenms;
GRANT ALL PRIVILEGES ON librenms.*
  TO 'librenms'@'<ip>'
  IDENTIFIED BY '<password>'
;
FLUSH PRIVILEGES;
exit

Replace <ip> above with the IP of the server running LibreNMS. If your database is on the same server as LibreNMS, you can just use localhost as the IP address.

If you are deploying a separate database server, you need to change the bind-address. If your MySQL database resides on the same server as LibreNMS, you should skip this step.

vim /etc/my.cnf

Add the following line:

bind-address = <ip>

Change <ip> to the IP address that your MySQL server should listen on. Restart MySQL:

service mysqld restart

On the NMS

Install necessary software. The packages listed below are an all-inclusive list of packages that were necessary on a clean install of CentOS 6.4. It also requires the EPEL repository.

rpm -Uvh http://download.fedoraproject.org/pub/epel/6/i386/epel-release-6-8.noarch.rpm
yum install php php-cli php-gd php-mysql php-snmp php-pear httpd net-snmp graphviz graphviz-php mysql ImageMagick  jwhois nmap mtr rrdtool MySQL-python net-snmp-utils vixie-cron php-mcrypt fping git
pear install Net_IPv4-1.3.4
pear install Net_IPv6-1.2.2b2
chkconfig --levels 235 httpd on
service httpd start

Cloning

You can clone the repository via HTTPS or SSH. In either case, you need to ensure the appropriate port (443 for HTTPS, 22 for SSH) is open in the outbound direction for your server.

cd /opt
git clone https://github.com/librenms/librenms.git librenms
cd /opt/librenms
cp config.php.default config.php
vim config.php

NOTE: The recommended method of cloning a git repository is HTTPS. If you would like to clone via SSH instead, use the command git clone git@github.com:librenms/librenms.git librenms instead.

Change the values to the right of the equal sign for lines beginning with $config[db_] to match your database information as setup above.

Change the value of $config['snmp']['community'] from public to whatever your read-only SNMP community is. If you have multiple communities, set it to the most common.

Add the following line to the end of config.php:

$config['fping'] = "/usr/sbin/fping";

Initiate the follow database with the following command:

php build-base.php

Create the admin user - priv should be 10

php adduser.php <name> <pass> 10

Substitute your desired username and password--and leave the angled brackets off.

Web Interface

To prepare the web interface (and adding devices shortly), you'll need to create and chown a directory as well as create an Apache vhost.

First, create and chown the rrd directory and create the logs directory

mkdir rrd logs
chown apache:apache rrd/

Note that if you're not running Ubuntu, you may need to change the owner to whomever the webserver runs as.

Next, add the following to /etc/httpd/conf.d/librenms.conf

<VirtualHost *:80>
  DocumentRoot /opt/librenms/html/
  ServerName  librenms.example.com
  CustomLog /opt/librenms/logs/access_log combined
  ErrorLog /opt/librenms/logs/error_log
  <Directory "/opt/librenms/html/">
    AllowOverride All
    Options FollowSymLinks MultiViews
  </Directory>
</VirtualHost>

Don't forget to restart Apache to make this active:

service httpd restart

Add localhost

php addhost.php localhost public v2c

This assumes you haven't made community changes--if you have, replace public with your community. It also assumes SNMP v2c. If you're using v3, there are additional steps (NOTE: instructions for SNMPv3 to come).

Discover localhost and poll it for the first time:

php discovery.php -h all && php poller.php -h all

The polling method used by LibreNMS is poller-wrapper.py, which was placed in the public domain by its author. By default, the LibreNMS cronjob runs poller- wrapper.py with 16 threads. The current LibreNMS recommendation is to use 4 th reads per core. The default if no thread count is 16 threads.

If the thread count needs to be changed, you can do so by editing librenms.cron before copying (or by editing /etc/cron.d/librenms if you've already copied the cron file). Just add a number after poller-wrapper.py, as in the below ex ample:

/opt/librenms/poller-wrapper.py 12 >> /dev/null 2>&1

Create the cronjob

cp librenms.cron /etc/cron.d/librenms

Daily Updates

LibreNMS performs daily updates by default. At 00:15 system time every day, a git pull --no-edit --quiet is performed. You can override this default by edit ing your config.php file. Remove the comment (the # mark) on the line:

#$config['update'] = 0;

so that it looks like this:

$config['update'] = 0;