mirror of
https://github.com/librenms/librenms.git
synced 2024-09-23 03:18:54 +00:00
23b0076209
Source: http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=CISCO-LWAPP-DOT11-CLIENT-MIB http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=CISCO-LWAPP-SYS-MIB http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=CISCO-LWAPP-TC-MIB
2150 lines
75 KiB
Plaintext
2150 lines
75 KiB
Plaintext
-- *******************************************************************
|
|
-- CISCO-LWAPP-SYS-MIB.my
|
|
-- March 2007, Devesh Pujari, Srinath Candadai
|
|
-- Feb 2011, Suja Thangaveluchamy
|
|
--
|
|
-- Copyright (c) 2007-2012 by Cisco Systems Inc.
|
|
-- All rights reserved.
|
|
-- *******************************************************************
|
|
|
|
CISCO-LWAPP-SYS-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE,
|
|
Unsigned32,
|
|
Counter32,
|
|
NOTIFICATION-TYPE
|
|
FROM SNMPv2-SMI
|
|
MODULE-COMPLIANCE,
|
|
OBJECT-GROUP,
|
|
NOTIFICATION-GROUP
|
|
FROM SNMPv2-CONF
|
|
RowStatus,
|
|
DisplayString,
|
|
TruthValue
|
|
FROM SNMPv2-TC
|
|
SnmpAdminString
|
|
FROM SNMP-FRAMEWORK-MIB
|
|
InetAddressType,
|
|
InetAddress,
|
|
InetPortNumber
|
|
FROM INET-ADDRESS-MIB
|
|
cldcClientAccessVLAN,
|
|
cldcClientMacAddress
|
|
FROM CISCO-LWAPP-DOT11-CLIENT-MIB
|
|
ciscoMgmt
|
|
FROM CISCO-SMI;
|
|
|
|
|
|
-- *******************************************************************
|
|
-- * MODULE IDENTITY
|
|
-- *******************************************************************
|
|
|
|
ciscoLwappSysMIB MODULE-IDENTITY
|
|
LAST-UPDATED "201208060000Z"
|
|
ORGANIZATION "Cisco Systems Inc."
|
|
CONTACT-INFO
|
|
"Cisco Systems,
|
|
Customer Service
|
|
Postal: 170 West Tasman Drive
|
|
San Jose, CA 95134
|
|
USA
|
|
Tel: +1 800 553-NETS
|
|
|
|
Email: cs-wnbu-snmp@cisco.com"
|
|
DESCRIPTION
|
|
"This MIB is intended to be implemented on all those
|
|
devices operating as Central controllers, that
|
|
terminate the Light Weight Access Point Protocol
|
|
tunnel from Cisco Light-weight LWAPP Access Points.
|
|
|
|
This MIB provides global configuration and status
|
|
information for the controller. All general system
|
|
related information is presented in this MIB.
|
|
|
|
The relationship between CC and the LWAPP APs
|
|
can be depicted as follows:
|
|
|
|
+......+ +......+ +......+
|
|
+ + + + + +
|
|
+ CC + + CC + + CC +
|
|
+ + + + + +
|
|
+......+ +......+ +......+
|
|
.. . .
|
|
.. . .
|
|
. . . .
|
|
. . . .
|
|
. . . .
|
|
. . . .
|
|
+......+ +......+ +......+ +......+
|
|
+ + + + + + + +
|
|
+ AP + + AP + + AP + + AP +
|
|
+ + + + + + + +
|
|
+......+ +......+ +......+ +......+
|
|
. . .
|
|
. . . .
|
|
. . . .
|
|
. . . .
|
|
. . . .
|
|
+......+ +......+ +......+ +......+
|
|
+ + + + + + + +
|
|
+ MN + + MN + + MN + + MN +
|
|
+ + + + + + + +
|
|
+......+ +......+ +......+ +......+
|
|
|
|
|
|
The LWAPP tunnel exists between the controller and
|
|
the APs. The MNs communicate with the APs through
|
|
the protocol defined by the 802.11 standard.
|
|
|
|
LWAPP APs, upon bootup, discover and join one of the
|
|
controllers and the controller pushes the configuration,
|
|
that includes the WLAN parameters, to the LWAPP APs.
|
|
The APs then encapsulate all the 802.11 frames from
|
|
wireless clients inside LWAPP frames and forward
|
|
the LWAPP frames to the controller.
|
|
|
|
GLOSSARY
|
|
|
|
Access Point ( AP )
|
|
|
|
An entity that contains an 802.11 medium access
|
|
control ( MAC ) and physical layer ( PHY ) interface
|
|
and provides access to the distribution services via
|
|
the wireless medium for associated clients.
|
|
|
|
LWAPP APs encapsulate all the 802.11 frames in
|
|
LWAPP frames and sends them to the controller to which
|
|
it is logically connected.
|
|
|
|
Light Weight Access Point Protocol ( LWAPP )
|
|
|
|
This is a generic protocol that defines the
|
|
communication between the Access Points and the
|
|
Central Controller.
|
|
|
|
Mobile Node ( MN )
|
|
|
|
A roaming 802.11 wireless device in a wireless
|
|
network associated with an access point. Mobile Node
|
|
and client are used interchangeably.
|
|
|
|
Extensible Authentication Protocol ( EAP )
|
|
|
|
EAP is a universal authentication protocol used in
|
|
wireless and PPP networks. It is defined by RFC 3748.
|
|
|
|
EAP-Flexible Authentication ( EAP-FAST )
|
|
|
|
This protocol is used via secure tunneling for 802.1X EAP.
|
|
|
|
PAC
|
|
|
|
PAC (Protected Access Credential) is a meachanism for
|
|
mutual authentication in EAP-FAST.
|
|
|
|
|
|
REFERENCE
|
|
|
|
[1] Wireless LAN Medium Access Control ( MAC ) and
|
|
Physical Layer ( PHY ) Specifications.
|
|
|
|
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
|
|
Weight Access Point Protocol.
|
|
|
|
[3] IEEE 802.1X - Authentication for Wireless and
|
|
Wired Connections."
|
|
REVISION "201208060000Z"
|
|
DESCRIPTION
|
|
"Added ciscoLwappSysConfigGroupSup1,
|
|
ciscoLwappSysMldConfigGroup, ciscoLwappSysConfigStatsGroup,
|
|
ciscoLwappSysAlarmObjectGroup, ciscoLwappSysThresholdGroup,
|
|
ciscoLwappSysHeartBeatGroup and ciscoLwappSysInfoGroup.
|
|
Deprecated ciscoLwappSysMIBComplianceRev2 and added
|
|
ciscoLwappSysMIBComplianceRev3"
|
|
REVISION "201206180000Z"
|
|
DESCRIPTION
|
|
"Added ciscoLwappSysPortConfigGroup,
|
|
ciscoLwappSysSecurityConfigGroup, ciscoLwappSysIgmpConfigGroup,
|
|
ciscoLwappSysSecNotifObjsGroup, ciscoLwappSysNotifsGroup and
|
|
ciscoLwappSysNotifControlGroup.
|
|
Deprecated ciscoLwappSysMIBComplianceRev1 and added
|
|
ciscoLwappSysMIBComplianceRev2"
|
|
REVISION "201002090000Z"
|
|
DESCRIPTION
|
|
"Updated clsTransferConfigGroup, ciscoLwappSysConfigGroupSup1.
|
|
Deprecate ciscoLwappSysMIBCompliance.
|
|
Added clsTransferConfig, clsSysArpProxyEnabled."
|
|
REVISION "200703140000Z"
|
|
DESCRIPTION
|
|
"Initial version of this MIB module."
|
|
::= { ciscoMgmt 618 }
|
|
|
|
|
|
ciscoLwappSysMIBNotifs OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIB 0 }
|
|
|
|
ciscoLwappSysMIBObjects OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIB 1 }
|
|
|
|
ciscoLwappSysMIBConform OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIB 2 }
|
|
|
|
-- This is reserved for objects in CISCO-LWAPP-LBS-MIB
|
|
-- ciscoLwappLbsMIB OBJECT IDENTIFIER ::= { ciscoLwappSysMIB 3 }
|
|
|
|
clsConfig OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 1 }
|
|
|
|
clsStatus OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 2 }
|
|
|
|
clsImageInfo OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 3 }
|
|
|
|
clsCpuInfo OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 4 }
|
|
|
|
clsSecurityGroup OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 5 }
|
|
|
|
ciscoLwappSysMIBNotifObjects OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 6 }
|
|
|
|
ciscoLwappSysMIBNotifControlObjects OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 7 }
|
|
|
|
clsSysInfo OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBObjects 8 }
|
|
|
|
|
|
clsDot3BridgeEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether 803.2 bridging
|
|
mode is enabled or disabled on the controller.
|
|
A value of 'true' specifies that the bridging
|
|
mode is enabled. A value of 'false' specifies
|
|
that the bridging mode is disabled."
|
|
::= { clsConfig 1 }
|
|
clsConfigDownload OBJECT IDENTIFIER
|
|
::= { clsConfig 2 }
|
|
|
|
clsConfigUpload OBJECT IDENTIFIER
|
|
::= { clsConfig 3 }
|
|
|
|
|
|
clsDownloadFileType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
code(2),
|
|
config(3),
|
|
webAuthCert(4),
|
|
webAdminCert(5),
|
|
signatures(6),
|
|
customWebAuth(7),
|
|
vendorDeviceCert(8),
|
|
vendorCaCert(9)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the file types that
|
|
can be downloaded to the controller.
|
|
The file types for download are:
|
|
unknown - Unknown file type
|
|
code - Code file
|
|
config - Configuration file
|
|
webAuthCert - Web authentication certificates
|
|
webAdminCert - Web administrative certificates
|
|
signatures - Signature file
|
|
customWebAuth - Custom web authentication
|
|
tar file
|
|
vendorDeviceCert - Vendor device certificates
|
|
vendorCaCert - Vendor certificate authority
|
|
certificates"
|
|
::= { clsConfigDownload 1 }
|
|
|
|
clsDownloadCertificateKey OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..255))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the key used
|
|
to encrypt the EAP certificate, specified
|
|
by IEEE 802.1X standard, during upload from
|
|
the controller and for decrypting the file
|
|
after its downloaded to the controller.
|
|
This object is relevant only when
|
|
clsDownloadFileType is 'vendorDeviceCert'.
|
|
For all other values of clsDownloadFileType
|
|
object this will return an empty string."
|
|
::= { clsConfigDownload 2 }
|
|
|
|
clsUploadFileType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
config(2),
|
|
errorLog(3),
|
|
systemTrace(4),
|
|
trapLog(5),
|
|
crashFile(6),
|
|
signatures(7),
|
|
pac(8),
|
|
radioCoreDump(9),
|
|
invalidConfig(10),
|
|
debugfile(11),
|
|
pktCapture(12),
|
|
watchdogCrash(13),
|
|
panicCrash(14),
|
|
vendorDevCert(15),
|
|
vendorCaCert(16),
|
|
webAdminCert(17),
|
|
webAuthCert(18)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the file types that
|
|
can be uploaded to the controller.
|
|
The file types for upload are:
|
|
unknown - Unknown file
|
|
config - Configuration file
|
|
errorLog - Error log
|
|
systemTrace - System trace
|
|
trapLog - Trap log
|
|
crashFile - Crash file
|
|
signatures - Signature file
|
|
pac - PAC file
|
|
radioCoreDump - AP's Radio core dump file
|
|
invalidConfig - Upload the file which contains the
|
|
invalid configuration commands feeded
|
|
by the downloaded Config file.
|
|
debugfile - Debug file.
|
|
pktCapture - Packet Capture File
|
|
watchdogCrash - Watchdog Crash Information File
|
|
panicCrash - Panic Crash Information File.
|
|
vendorDevCert - EAP ca certificate.
|
|
vendorCaCert - EAP dev certificate.
|
|
webAdminCert - Web Admin certificate.
|
|
webAuthCert - Web Auth certificate."
|
|
::= { clsConfigUpload 1 }
|
|
|
|
clsUploadPacUsername OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..63))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the upload user name
|
|
for protected access credential (PAC). This
|
|
object needs to be set before setting
|
|
clsUploadFileType to 'pac'. For all other
|
|
values of clsUploadFileType this will return
|
|
an empty string."
|
|
::= { clsConfigUpload 2 }
|
|
|
|
clsUploadPacPassword OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the upload password for
|
|
protected access credential (PAC). This object
|
|
needs to be set before setting clsUploadFileType
|
|
to 'pac'. For all other values of
|
|
clsUploadFileType this will return an empty
|
|
string."
|
|
::= { clsConfigUpload 3 }
|
|
|
|
clsUploadPacValidity OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..65535)
|
|
UNITS "days"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the upload validity in
|
|
days for protected access credential (PAC).
|
|
This object is relevant only when
|
|
clsUploadFileType is set to 'pac'.
|
|
For all other values of clsUploadFileType
|
|
this will return an empty string."
|
|
::= { clsConfigUpload 4 }
|
|
clsTransferConfigGroup OBJECT IDENTIFIER
|
|
::= { clsConfig 4 }
|
|
|
|
|
|
clsTransferConfigFileEncryption OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disable(1),
|
|
enable(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The configuration file can be encrypted before
|
|
upload from the controller and then decrypted
|
|
before downloading to the controller when this
|
|
option is enabled.
|
|
This is applicable only when clsDownloadFileType,
|
|
clsUploadFileType is set to Config."
|
|
::= { clsTransferConfigGroup 1 }
|
|
|
|
clsTransferConfigFileEncryptionKey OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..16))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the key to be used when encrypting the
|
|
configuration file while upload from the controller
|
|
or while decrypting the file after download to
|
|
the controller.
|
|
This is applicable only when clsDownloadFileType,
|
|
clsUploadFileType is set to Config."
|
|
::= { clsTransferConfigGroup 2 }
|
|
clsTransferConfig OBJECT IDENTIFIER
|
|
::= { clsConfig 8 }
|
|
|
|
|
|
clsTransferConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF ClsTransferConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table is used to configure the server details
|
|
which will be used
|
|
by the controller to upload/download files."
|
|
::= { clsTransferConfig 1 }
|
|
|
|
clsTransferConfigEntry OBJECT-TYPE
|
|
SYNTAX ClsTransferConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry in this table provides information about
|
|
the server to which the controller will
|
|
upload/download files."
|
|
INDEX {
|
|
clsTransferType,
|
|
clsTransferMode
|
|
}
|
|
::= { clsTransferConfigTable 1 }
|
|
|
|
ClsTransferConfigEntry ::= SEQUENCE {
|
|
clsTransferType INTEGER,
|
|
clsTransferMode INTEGER,
|
|
clsTransferServerAddressType InetAddressType,
|
|
clsTransferServerAddress InetAddress,
|
|
clsTransferPath SnmpAdminString,
|
|
clsTransferFilename SnmpAdminString,
|
|
clsTransferFtpUsername SnmpAdminString,
|
|
clsTransferFtpPassword SnmpAdminString,
|
|
clsTransferFtpPortNum InetPortNumber,
|
|
clsTransferTftpMaxRetries Unsigned32,
|
|
clsTransferTftpTimeout Unsigned32,
|
|
clsTransferStart INTEGER,
|
|
clsTransferStatus INTEGER,
|
|
clsTransferStatusString SnmpAdminString
|
|
}
|
|
|
|
clsTransferType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
download(1),
|
|
upload(2)
|
|
}
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Transfer type configures the type of operation
|
|
with the server by the controller. The mode is
|
|
either Upload or Download."
|
|
::= { clsTransferConfigEntry 1 }
|
|
|
|
clsTransferMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
tftp(1),
|
|
ftp(2),
|
|
sftp(3)
|
|
}
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Transfer mode configures the mode of transfer used
|
|
by the controller with the server. The mode is
|
|
either TFTP or FTP/SFTP."
|
|
::= { clsTransferConfigEntry 2 }
|
|
|
|
clsTransferServerAddressType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the address type of
|
|
the Server to which the controller will transfer the file."
|
|
::= { clsTransferConfigEntry 3 }
|
|
|
|
clsTransferServerAddress OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the address of the Server to
|
|
which the controller will transfer the file."
|
|
::= { clsTransferConfigEntry 4 }
|
|
|
|
clsTransferPath OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Transfer path configures the directory
|
|
path for file transfer. The controller
|
|
remembers the last file path used."
|
|
::= { clsTransferConfigEntry 5 }
|
|
|
|
clsTransferFilename OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Transfer filename configures the file name for the
|
|
file being transferred from the controller.
|
|
The controller remembers the last file
|
|
name used. An example would be File Path
|
|
set to c:\tftp\code\ and File Name set to
|
|
e1r1v1.opr."
|
|
::= { clsTransferConfigEntry 6 }
|
|
|
|
clsTransferFtpUsername OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..31))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to store the FTP username for
|
|
transferring file on the server.
|
|
This is valid only for FTP transfer mode."
|
|
::= { clsTransferConfigEntry 7 }
|
|
|
|
clsTransferFtpPassword OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..31))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to store the FTP password for
|
|
transferring file on the server.
|
|
This is valid only for FTP transfer mode."
|
|
::= { clsTransferConfigEntry 8 }
|
|
|
|
clsTransferFtpPortNum OBJECT-TYPE
|
|
SYNTAX InetPortNumber
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to store the port number to be used
|
|
by the FTP protocol while connecting to the server.
|
|
This is valid only for FTP transfer mode."
|
|
DEFVAL { 21 }
|
|
::= { clsTransferConfigEntry 9 }
|
|
|
|
clsTransferTftpMaxRetries OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..254)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Maximum number of retries to be allowed for a
|
|
TFTP message packet.
|
|
This is valid only for TFTP transfer mode."
|
|
DEFVAL { 10 }
|
|
::= { clsTransferConfigEntry 10 }
|
|
|
|
clsTransferTftpTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..254)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Timeout in seconds for a TFTP message packet.
|
|
This is valid only for TFTP transfer mode."
|
|
DEFVAL { 6 }
|
|
::= { clsTransferConfigEntry 11 }
|
|
|
|
clsTransferStart OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
none(1),
|
|
initiate(2),
|
|
initiatePeer(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Transfer start will start the file transfer operation
|
|
on Active when it is set to initiate(2), it will
|
|
return none(1) for GET. Transfer start will start
|
|
the file transfer operation on Standby when it
|
|
is set to initiatePeer(3),"
|
|
::= { clsTransferConfigEntry 12 }
|
|
|
|
clsTransferStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
notInitiated(1),
|
|
transferStarting(2),
|
|
errorStarting(3),
|
|
wrongFileType(4),
|
|
updatingConfig(5),
|
|
invalidConfigFile(6),
|
|
writingToFlash(7),
|
|
failureWritingToFlash(8),
|
|
checkingCRC(9),
|
|
failedCRC(10),
|
|
unknownDirection(11),
|
|
transferSuccessful(12),
|
|
transferFailed(13),
|
|
bootBreakOff(14),
|
|
invalidTarFile(15),
|
|
unknown(99)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the current status of a transfer.
|
|
|
|
Following are valid only when clsTransferType
|
|
is 'download' :-
|
|
bootBreakOff(14), invalidTarFile(15)."
|
|
::= { clsTransferConfigEntry 13 }
|
|
|
|
clsTransferStatusString OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..255))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates in string format about the current
|
|
status of a transfer."
|
|
::= { clsTransferConfigEntry 14 }
|
|
|
|
|
|
clsConfigGeneral OBJECT IDENTIFIER
|
|
::= { clsConfig 5 }
|
|
|
|
|
|
clsTimeZone OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object timezone for the controller.
|
|
Enter the timezone location index.
|
|
1. (GMT-12:00) International Date Line West
|
|
2. (GMT-11:00) Samoa
|
|
3. (GMT-10:00) Hawaii
|
|
4. (GMT -9:00) Alaska
|
|
5. (GMT -8:00) Pacific Time (US and Canada)
|
|
6. (GMT -7:00) Mountain Time (US and Canada)
|
|
7. (GMT -6:00) Central Time (US and Canada)
|
|
8. (GMT -5:00) Eastern Time (US and Canada)
|
|
9. (GMT -4:00) Altantic Time (Canada)
|
|
10. (GMT -3:00) Buenos Aires (Agentina)
|
|
11. (GMT -2:00) Mid-Atlantic
|
|
12. (GMT -1:00) Azores
|
|
13. (GMT) London, Lisbon, Dublin, Edinburgh
|
|
14. (GMT +1:00) Amsterdam, Berlin, Rome, Vienna
|
|
15. (GMT +2:00) Jerusalem
|
|
16. (GMT +3:00) Baghdad
|
|
17. (GMT +4:00) Muscat, Abu Dhabi
|
|
18. (GMT +4:30) Kabul
|
|
19. (GMT +5:00) Karachi, Islamabad, Tashkent
|
|
20. (GMT +5:30) Colombo, Kolkata, Mumbai, New Delhi
|
|
21. (GMT +5:45) Katmandu
|
|
22. (GMT +6:00) Almaty, Novosibirsk
|
|
23. (GMT +6:30) Rangoon
|
|
24. (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar
|
|
25. (GMT +8:00) HongKong, Bejing, Chongquing
|
|
26. (GMT +9:00) Tokyo, Osaka, Sapporo
|
|
27. (GMT +9:30) Darwin
|
|
28. (GMT+10:00) Sydney, Melbourne, Canberra
|
|
29. (GMT+11:00) Magadan, Solomon Is., New Caledonia
|
|
30. (GMT+12:00) Kamchatka, Marshall Is., Fiji"
|
|
::= { clsConfigGeneral 1 }
|
|
|
|
clsTimeZoneDescription OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the timezone description
|
|
for the controller."
|
|
::= { clsConfigGeneral 2 }
|
|
|
|
clsMaxClientsTrapThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Percent"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the threshold number
|
|
of clients on the controller to trigger a trap.
|
|
The trap ciscoLwappMaxClientsReached
|
|
will be triggered once the count of clients
|
|
on the controller reaches this limit and the
|
|
clsMaxClientsTrapEnabled is enabled."
|
|
::= { clsConfigGeneral 3 }
|
|
|
|
clsMaxRFIDTagsTrapThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Percent"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the threshold number
|
|
of RFID tags on the controller to trigger a trap.
|
|
The trap ciscoLwappMaxRFIDTagsReached
|
|
will be triggered once the count of RFID tags
|
|
on the controller reaches this limit and the
|
|
clsMaxRFIDTagsTrapEnabled is enabled."
|
|
::= { clsConfigGeneral 4 }
|
|
clsSyslogIpConfig OBJECT IDENTIFIER
|
|
::= { clsConfig 6 }
|
|
|
|
|
|
cLSysLogConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CLSysLogConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table is used to configure multiple syslog servers
|
|
to which the the syslog messages will be sent to by the
|
|
controller."
|
|
::= { clsSyslogIpConfig 1 }
|
|
|
|
cLSysLogConfigEntry OBJECT-TYPE
|
|
SYNTAX CLSysLogConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry in this table provides information about
|
|
the host to which the syslog messages will be sent to."
|
|
INDEX { cLSysLogServerIndex }
|
|
::= { cLSysLogConfigTable 1 }
|
|
|
|
CLSysLogConfigEntry ::= SEQUENCE {
|
|
cLSysLogServerIndex Unsigned32,
|
|
cLSysLogAddressType InetAddressType,
|
|
cLSysLogAddress InetAddress,
|
|
cLSysLogHostRowStatus RowStatus
|
|
}
|
|
|
|
cLSysLogServerIndex OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the index of the host to
|
|
which syslog messages will be sent."
|
|
::= { cLSysLogConfigEntry 1 }
|
|
|
|
cLSysLogAddressType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the address type of
|
|
the host to which syslog messages will be sent.
|
|
'dns' is used when the hostname of the server
|
|
is configured."
|
|
::= { cLSysLogConfigEntry 2 }
|
|
|
|
cLSysLogAddress OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the ipaddress or hostname
|
|
of the host to which syslog messages will be sent."
|
|
::= { cLSysLogConfigEntry 3 }
|
|
|
|
cLSysLogHostRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the status column for this row and is used
|
|
to create and delete specific instances of rows in
|
|
this table."
|
|
::= { cLSysLogConfigEntry 4 }
|
|
|
|
|
|
|
|
cLSysArpUnicastEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether ARP unicast
|
|
is enabled or disabled on the controller.
|
|
A value of 'true' specifies that the ARP
|
|
unicast is enabled. A value of 'false' specifies
|
|
that the ARP unicast is disabled."
|
|
::= { clsConfig 7 }
|
|
|
|
cLSysBroadcastForwardingEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether broadcast forwarding
|
|
is enabled or disabled on the controller.
|
|
A value of 'true' specifies that the broadcast
|
|
forwarding is enabled. A value of 'false' specifies
|
|
that the broadcast forwarding is disabled."
|
|
::= { clsConfig 9 }
|
|
|
|
cLSysLagModeEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether Link Aggregation(LAG)
|
|
mode is enabled or disabled on the controller.
|
|
A value of 'true' specifies that the LAG mode
|
|
is enabled. A value of 'false' specifies
|
|
that the LAG mode is disabled on the controller."
|
|
::= { clsConfig 10 }
|
|
|
|
clsConfigProductBranchVersion OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This string contains the branch name of the specific
|
|
controller branch. For Mesh branches, this string has
|
|
the value M(Mesh). Zero length string is returned if
|
|
there is no branch name. This string is append to the
|
|
product version for display purposes. For example,
|
|
if the mesh product version is 4.1.191.10, a manager
|
|
application may display the version string as
|
|
4.1.191.10M (Mesh)"
|
|
::= { clsConfig 11 }
|
|
|
|
clsConfigDhcpProxyEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents whether the DHCP proxy option is
|
|
enabled or disabled.
|
|
A value of 'true' specifies that the proxy option is enabled
|
|
on the controller.
|
|
A value of 'false' specifies that the proxy option
|
|
is disabled on the controller."
|
|
DEFVAL { false }
|
|
::= { clsConfig 12 }
|
|
cLSysMulticastIGMP OBJECT IDENTIFIER
|
|
::= { clsConfig 13 }
|
|
|
|
|
|
cLSysMulticastIGMPSnoopingEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether Multicast IGMP
|
|
Snooping is enabled or disabled on the controller.
|
|
A value of 'true' specifies that
|
|
the Multicast IGMP Snooping is enabled. To enable this,
|
|
agentNetworkMulticastMode/clsConfigMulticastEnabled must
|
|
not be in disabled state. A value of 'false'
|
|
specifies that the Multicast IGMP Snooping is
|
|
disabled on the controller."
|
|
DEFVAL { false }
|
|
::= { cLSysMulticastIGMP 1 }
|
|
|
|
cLSysMulticastIGMPSnoopingTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the IGMP timeout, in seconds.
|
|
To set this value, cLSysMulticastIGMPSnoopingEnabled
|
|
must be set to True. When the timeout expires,
|
|
the controller sends a query on all WLANs, causing
|
|
all clients that are listening to a multicast group
|
|
to send a packet back to the controller."
|
|
::= { cLSysMulticastIGMP 2 }
|
|
|
|
cLSysMulticastIGMPQueryInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the IGMP query interval, in seconds.
|
|
To set this value, cLSysMulticastIGMPSnoopingEnabled must
|
|
be set to True."
|
|
::= { cLSysMulticastIGMP 3 }
|
|
-- ******************************************************************
|
|
-- clsPortModeConfigTable
|
|
--
|
|
-- ******************************************************************
|
|
|
|
cLSPortModeConfig OBJECT IDENTIFIER
|
|
::= { clsConfig 14 }
|
|
|
|
|
|
clsPortModeConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF ClsPortModeConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains the entries for physical
|
|
port related parameters"
|
|
::= { cLSPortModeConfig 1 }
|
|
|
|
clsPortModeConfigEntry OBJECT-TYPE
|
|
SYNTAX ClsPortModeConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This entry contains the Switch's physical
|
|
port phyical mode related attribues"
|
|
INDEX { clsPortDot1dBasePort }
|
|
::= { clsPortModeConfigTable 1 }
|
|
|
|
ClsPortModeConfigEntry ::= SEQUENCE {
|
|
clsPortDot1dBasePort Unsigned32,
|
|
clsPortModePhysicalMode INTEGER,
|
|
clsPortModePhysicalStatus INTEGER,
|
|
clsPortModeSfpType SnmpAdminString,
|
|
clsPortUpDownCount Counter32
|
|
}
|
|
|
|
clsPortDot1dBasePort OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is a unique unsigned integer value which identifies
|
|
the base port number."
|
|
::= { clsPortModeConfigEntry 1 }
|
|
|
|
clsPortModePhysicalMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
autoNegotiate(1),
|
|
half10(2),
|
|
full10(3),
|
|
half100(4),
|
|
full100(5),
|
|
full1000sx(6),
|
|
half1000(7),
|
|
full1000(8),
|
|
half10000(9),
|
|
full10000(10)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The switch's Port Speed Mode. This is the
|
|
configured physical mode."
|
|
::= { clsPortModeConfigEntry 2 }
|
|
|
|
clsPortModePhysicalStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
autonegotiate(2),
|
|
half10(3),
|
|
full10(4),
|
|
half100(5),
|
|
full100(6),
|
|
full1000sx(7),
|
|
half1000(8),
|
|
full1000(9),
|
|
half10000(10),
|
|
full10000(11)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The switch's Port Physical Speed Status.This
|
|
is the current actual speed."
|
|
::= { clsPortModeConfigEntry 3 }
|
|
|
|
clsPortModeSfpType OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the SFP's type
|
|
of the port."
|
|
::= { clsPortModeConfigEntry 4 }
|
|
|
|
clsPortUpDownCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the total number
|
|
of up/down count of the port. Every time
|
|
the value of ifOperStatus is changed,
|
|
this MIB should be incremented."
|
|
::= { clsPortModeConfigEntry 5 }
|
|
|
|
|
|
clsCoreDump OBJECT IDENTIFIER
|
|
::= { clsConfig 15 }
|
|
|
|
|
|
clsCoreDumpTransferEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether the core dump
|
|
file transfer is enabled or disabled. If the
|
|
value is True the core-dump feature is Enabled
|
|
otherwise Disabled."
|
|
DEFVAL { false }
|
|
::= { clsCoreDump 1 }
|
|
|
|
clsCoreDumpTransferMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
ftp(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This Object specifies the Core Dump Transfer Mode.
|
|
If the value is FTP then only FTP attributes
|
|
clsCoreDumpServerIPAddress, clsCoreDumpFileName,
|
|
clsCoreDumpUserName, clsCoreDumpPassword can be set,
|
|
unknown value is not SETable."
|
|
::= { clsCoreDump 2 }
|
|
|
|
clsCoreDumpServerIPAddressType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This Object Id Specifies the IP Address Type of Server."
|
|
::= { clsCoreDump 3 }
|
|
|
|
clsCoreDumpServerIPAddress OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the IP Address of the Server
|
|
where the core-dump will be uploaded."
|
|
::= { clsCoreDump 4 }
|
|
|
|
clsCoreDumpFileName OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the File Name of the core-dump by
|
|
which you want to save it on the
|
|
Server."
|
|
::= { clsCoreDump 5 }
|
|
|
|
clsCoreDumpUserName OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Login Name at the FTP server."
|
|
::= { clsCoreDump 6 }
|
|
|
|
clsCoreDumpPassword OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Login Password of the FTP server."
|
|
::= { clsCoreDump 7 }
|
|
|
|
clsConfigMulticastEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents whether global multicast is
|
|
enabled or disabled.
|
|
A value of 'true' specifies that the multicast option
|
|
is enabled on the controller.
|
|
A value of 'false' specifies that the multicast option
|
|
is disabled on the controller."
|
|
DEFVAL { false }
|
|
::= { clsConfig 16 }
|
|
cLSysMulticastMLD OBJECT IDENTIFIER
|
|
::= { clsConfig 17 }
|
|
|
|
|
|
cLSysMulticastMLDSnoopingEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether Multicast MLD Snooping
|
|
is enabled or disabled on the controller. A value of
|
|
'true' specifies that the Multicast MLD Snooping is
|
|
enabled. To enable this, agentNetworkMulticastMode/
|
|
clsConfigMulticastEnabled must not be
|
|
in disabled state. A value of 'false' specifies
|
|
that the Multicast MLD Snooping is disabled
|
|
on the controller."
|
|
DEFVAL { false }
|
|
::= { cLSysMulticastMLD 1 }
|
|
|
|
cLSysMulticastMLDSnoopingTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the MLD timeout, in seconds.
|
|
To set this value, cLSysMulticastMLDSnoopingEnabled
|
|
must be set to True. When the timeout expires,
|
|
the controller sends a query on all WLANs, causing all
|
|
clients that are listening to a multicast group
|
|
to send a packet back to the controller."
|
|
::= { cLSysMulticastMLD 2 }
|
|
|
|
cLSysMulticastMLDQueryInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the MLD query interval, in seconds.
|
|
To set this value, cLSysMulticastMLDSnoopingEnabled
|
|
must be set to True."
|
|
::= { cLSysMulticastMLD 3 }
|
|
-- stats-timer config.
|
|
|
|
clsConfigStats OBJECT IDENTIFIER
|
|
::= { clsConfig 18 }
|
|
|
|
|
|
-- ********************************************************************
|
|
-- * System Realtime Stats Timer Interval
|
|
-- ********************************************************************
|
|
|
|
clsSysRealtimeStatsTimer OBJECT-TYPE
|
|
SYNTAX Unsigned32 (2..5)
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the realtime stats interval
|
|
of the system. There are 2 stats modes: realtime and
|
|
normal. realtime interval is much less than normal mode."
|
|
DEFVAL { 5 }
|
|
::= { clsConfigStats 1 }
|
|
|
|
-- ********************************************************************
|
|
-- * System Normal Stats Timer Interval
|
|
-- ********************************************************************
|
|
|
|
clsSysNormalStatsTimer OBJECT-TYPE
|
|
SYNTAX Unsigned32 (10..180)
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the normal stats interval
|
|
of the system. There are 2 stats modes: realtime
|
|
and normal. realtime interval is much less than
|
|
normal mode."
|
|
DEFVAL { 180 }
|
|
::= { clsConfigStats 2 }
|
|
|
|
-- ********************************************************************
|
|
-- * System Sampling Statistics Interval
|
|
-- ********************************************************************
|
|
|
|
clsSysStatsSamplingInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the sampling interval of the system,
|
|
which is applied to WLC and APs connected to this WLC.
|
|
WLC and APs poll specific data every sampling interval."
|
|
::= { clsConfigStats 3 }
|
|
|
|
-- ********************************************************************
|
|
-- * System Average Statistics Interval
|
|
-- ********************************************************************
|
|
|
|
clsSysStatsAverageInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the average statistics interval of
|
|
the system, which is applied to WLC and APs connected to
|
|
this WLC. This interval works as a time window for
|
|
calculating the average value of the data polled by WLC/AP
|
|
every sampling interval."
|
|
::= { clsConfigStats 4 }
|
|
-- Alarm service config.
|
|
|
|
clsAlarmObjects OBJECT IDENTIFIER
|
|
::= { clsConfig 19 }
|
|
|
|
|
|
-- ********************************************************************
|
|
-- * Alarm Hold Time
|
|
-- ********************************************************************
|
|
|
|
clsAlarmHoldTime OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..3600)
|
|
UNITS "second"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the time in seconds for which
|
|
an alarm object should be soaked when its on/off
|
|
state is changed."
|
|
DEFVAL { 6 }
|
|
::= { clsAlarmObjects 1 }
|
|
|
|
-- ********************************************************************
|
|
-- * Alarm Retransmit Interval
|
|
-- ********************************************************************
|
|
|
|
clsAlarmTrapRetransmitInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..65535)
|
|
UNITS "second"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the interval in seconds in
|
|
which alarm traps, if any, are retransmitted.
|
|
Setting this value to 0 means no retransmission."
|
|
DEFVAL { 0 }
|
|
::= { clsAlarmObjects 2 }
|
|
-- System-wide thresholds config.
|
|
|
|
clsSysThresholdConfig OBJECT IDENTIFIER
|
|
::= { clsConfig 20 }
|
|
|
|
|
|
-- ********************************************************************
|
|
-- * Controller CPU usage threshold
|
|
-- ********************************************************************
|
|
|
|
clsSysControllerCpuUsageThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..100)
|
|
UNITS "Percent"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the CPU usage threshold on a
|
|
controller.
|
|
Setting this value to 0 means no threshold."
|
|
DEFVAL { 0 }
|
|
::= { clsSysThresholdConfig 1 }
|
|
|
|
-- ********************************************************************
|
|
-- * Controller memory usage threshold
|
|
-- ********************************************************************
|
|
|
|
clsSysControllerMemoryUsageThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..100)
|
|
UNITS "Percent"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the memory usage threshold on a
|
|
controller.
|
|
Setting this value to 0 means no threshold."
|
|
DEFVAL { 0 }
|
|
::= { clsSysThresholdConfig 2 }
|
|
|
|
-- ********************************************************************
|
|
-- * AP CPU usage threshold
|
|
-- ********************************************************************
|
|
|
|
clsSysApCpuUsageThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..100)
|
|
UNITS "Percent"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the CPU usage threshold on a
|
|
AP.
|
|
Setting this value to 0 means no threshold."
|
|
DEFVAL { 0 }
|
|
::= { clsSysThresholdConfig 3 }
|
|
|
|
-- ********************************************************************
|
|
-- * AP memory usage threshold
|
|
-- ********************************************************************
|
|
|
|
clsSysApMemoryUsageThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..100)
|
|
UNITS "Percent"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the memory usage threshold on a
|
|
AP.
|
|
Setting this value to 0 means no threshold."
|
|
DEFVAL { 0 }
|
|
::= { clsSysThresholdConfig 4 }
|
|
clsNMHeartBeat OBJECT IDENTIFIER
|
|
::= { clsConfig 21 }
|
|
|
|
|
|
clsNMHeartBeatEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether heart beat trap to network
|
|
manager is enabled or disabled. If the value is True the
|
|
Network Manager Heart Beat feature is Enabled otherwise
|
|
Disabled."
|
|
DEFVAL { false }
|
|
::= { clsNMHeartBeat 1 }
|
|
|
|
clsNMHeartBeatInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..65535)
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the interval in seconds in heart beat
|
|
traps to network manager."
|
|
DEFVAL { 180 }
|
|
::= { clsNMHeartBeat 2 }
|
|
|
|
clsCrashSystem OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object resets the switch with a crash.
|
|
If a value of of 'true' is set, the swicth would crash.
|
|
GET on this object would return 'false'."
|
|
::= { clsConfig 99 }
|
|
|
|
-- ********************************************************************
|
|
-- * Status Objects
|
|
-- ********************************************************************
|
|
|
|
cLSysLagModeInTransition OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether the LAG mode is
|
|
in transition on the controller.
|
|
A value of 'true' specifies that the LAG mode
|
|
is in transition and the controller has to be rebooted
|
|
to take effect.A value of 'false' specifies
|
|
that the LAG mode is not in transition."
|
|
::= { clsStatus 1 }
|
|
|
|
-- ********************************************************************
|
|
-- * Emergency Image Version
|
|
-- ********************************************************************
|
|
|
|
clsEmergencyImageVersion OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cisco recommends installing Cisco Unified Wireless Network
|
|
Controller Boot Software , (*_ER.aes , where star denotes
|
|
the version of the controller image ) on all controller
|
|
platforms. If this ER.aes is not installed, the controller
|
|
would not be able to show the Emergency Image Version
|
|
correctly(or Field Recovery Image Version), and would be shown
|
|
as 'N/A'. The ER.aes files are independent from the controller
|
|
software files. Any controller software file can be run
|
|
with any ER.aes file. However, installing the latest boot
|
|
software file (*_ER.aes , where star denotes the controller
|
|
version) ensures that the boot software modifications in
|
|
all of the previous and current
|
|
boot software ER.aes files are installed."
|
|
::= { clsImageInfo 1 }
|
|
|
|
-- ********************************************************************
|
|
-- Security oids
|
|
-- ********************************************************************
|
|
|
|
clsSecStrongPwdCaseCheck OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the case check for the
|
|
passwords configured in controller.
|
|
When enabled, the new password must contain characters from
|
|
at least three of the following classes : lowercase letters,
|
|
uppercase letters, digits and special characters."
|
|
::= { clsSecurityGroup 1 }
|
|
|
|
clsSecStrongPwdConsecutiveCheck OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the consecutive
|
|
check for the passwords configured in controller.
|
|
When enabled, the password provided should not have
|
|
a character repeated more than thrice consecutively."
|
|
::= { clsSecurityGroup 2 }
|
|
|
|
clsSecStrongPwdDefaultCheck OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the default check
|
|
for the passwords configured in controller.
|
|
When enabled, the new password must not be 'cisco',
|
|
'ocsic', 'admin', 'nimda' or any variant obtained by
|
|
changing the capitalization of letters therein,
|
|
or by substituting '1' '|' or '!' for i, and/or
|
|
substituting '0' for 'o',
|
|
and/or substituting '$' for 's'"
|
|
::= { clsSecurityGroup 3 }
|
|
|
|
clsSecStrongPwdAsUserNameCheck OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the username check
|
|
for the password configured in controller.
|
|
When enabled the new password must not be same as
|
|
the associated username or the reversed username."
|
|
::= { clsSecurityGroup 4 }
|
|
|
|
-- ********************************************************************
|
|
-- * System Flash Size
|
|
-- ********************************************************************
|
|
|
|
clsSysFlashSize OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the total flash memory size in Kbytes."
|
|
::= { clsSysInfo 1 }
|
|
|
|
-- ********************************************************************
|
|
-- * System Memory Type
|
|
-- ********************************************************************
|
|
|
|
clsSysMemoryType OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the system memory type."
|
|
::= { clsSysInfo 2 }
|
|
|
|
-- ********************************************************************
|
|
-- * System Supported MAX Clients
|
|
-- ********************************************************************
|
|
|
|
clsSysMaxClients OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies max associated clients
|
|
supported per WLC"
|
|
::= { clsSysInfo 3 }
|
|
|
|
-- ********************************************************************
|
|
-- * Number of connected AP's
|
|
-- ********************************************************************
|
|
|
|
clsSysApConnectCount OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the count of AP's that are
|
|
connected with WLC"
|
|
::= { clsSysInfo 4 }
|
|
|
|
clsSysNetId OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (0..32))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the SysNetId which is the
|
|
numeric string to identify the system information
|
|
like SysName"
|
|
::= { clsSysInfo 5 }
|
|
|
|
-- ********************************************************************
|
|
-- * WLC System Current Memory Usage
|
|
-- ********************************************************************
|
|
|
|
clsSysCurrentMemoryUsage OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the current percent usage
|
|
of system memory. This MIB should be updated
|
|
every clsSysStatsSamplingInterval."
|
|
::= { clsSysInfo 6 }
|
|
|
|
-- ********************************************************************
|
|
-- * WLC System Average Memory Usage
|
|
-- ********************************************************************
|
|
|
|
clsSysAverageMemoryUsage OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the average percent usage
|
|
of system memory. The memory average usage should be
|
|
the average of memory-Usage during the time window
|
|
specified by clsSysStatsAverageInterval."
|
|
::= { clsSysInfo 7 }
|
|
|
|
-- ********************************************************************
|
|
-- * WLC System Current CPU Usage
|
|
-- ********************************************************************
|
|
|
|
clsSysCurrentCpuUsage OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the current percent usage of all CPUs.
|
|
This MIB should be updated every clsSysStatsSamplingInterval."
|
|
::= { clsSysInfo 8 }
|
|
|
|
-- ********************************************************************
|
|
-- * WLC System Average CPU Usage
|
|
-- ********************************************************************
|
|
|
|
clsSysAverageCpuUsage OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the average percent CPU usage.
|
|
The average CPU usage should be the average of CPU-Usage
|
|
during the time window specified by
|
|
clsSysStatsAverageInterval."
|
|
::= { clsSysInfo 9 }
|
|
|
|
-- ********************************************************************
|
|
-- * System Cpu Type
|
|
-- ********************************************************************
|
|
|
|
clsSysCpuType OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the cpu type."
|
|
::= { clsSysInfo 10 }
|
|
|
|
clsMaxRFIDTagsCount OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the maximum RFID tags present
|
|
on the controller."
|
|
::= { clsSysInfo 11 }
|
|
|
|
clsMaxClientsCount OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the maximum clients present
|
|
on the controller."
|
|
::= { clsSysInfo 12 }
|
|
|
|
-- ********************************************************************
|
|
-- * Notification Control Object
|
|
-- ********************************************************************
|
|
|
|
clsSecStrongPwdCheckTrapEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether the
|
|
ciscoLwappStrongPwdCheck notification would be generated.
|
|
|
|
A value of 'true' indicates that the agent generates
|
|
ciscoLwappStrongPwdCheck notification.
|
|
|
|
A value of 'false' indicates that the agent doesn't
|
|
generate ciscoLwappStrongPwdCheck notification."
|
|
DEFVAL { true }
|
|
::= { ciscoLwappSysMIBNotifControlObjects 1 }
|
|
|
|
clsMaxClientsTrapEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether the
|
|
ciscoLwappMaxClientsReached notification would be generated.
|
|
|
|
A value of 'true' indicates that the agent generates
|
|
ciscoLwappMaxClientsReached notification.
|
|
|
|
A value of 'false' indicates that the agent doesn't
|
|
generate ciscoLwappMaxClientsReached notification."
|
|
DEFVAL { true }
|
|
::= { ciscoLwappSysMIBNotifControlObjects 2 }
|
|
|
|
clsMaxRFIDTagsTrapEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether the
|
|
ciscoLwappMaxRFIDTagsReached notification would be generated.
|
|
|
|
A value of 'true' indicates that the agent generates
|
|
ciscoLwappMaxRFIDTagsReached notification.
|
|
|
|
A value of 'false' indicates that the agent doesn't
|
|
generate ciscoLwappMaxRFIDTagsReached notification."
|
|
DEFVAL { true }
|
|
::= { ciscoLwappSysMIBNotifControlObjects 3 }
|
|
|
|
-- ********************************************************************
|
|
-- * Notification Objects
|
|
-- ********************************************************************
|
|
|
|
clsSecStrongPwdManagementUser OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (1..24))
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the management user who
|
|
enabled/disabled the strong password checks."
|
|
::= { ciscoLwappSysMIBNotifObjects 1 }
|
|
|
|
clsSecStrongPwdCheckType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
caseCheck(1),
|
|
consecutiveCheck(2),
|
|
defaultCheck(3),
|
|
usernameCheck(4),
|
|
allChecks(5)
|
|
}
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the type of the check that was
|
|
enabled/disabled by the management user."
|
|
::= { ciscoLwappSysMIBNotifObjects 2 }
|
|
|
|
clsSecStrongPwdCheckOption OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether the strong password check
|
|
was enabled/disabled."
|
|
::= { ciscoLwappSysMIBNotifObjects 3 }
|
|
|
|
clsSysAlarmSet OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether this system alarm is
|
|
raise or clear.
|
|
A value of 'true' indicates this event is set.
|
|
A value of 'false' indicates this even is cleared."
|
|
::= { ciscoLwappSysMIBNotifObjects 4 }
|
|
|
|
-- ********************************************************************
|
|
-- * Notifications
|
|
-- ********************************************************************
|
|
|
|
ciscoLwappSysInvalidXmlConfig NOTIFICATION-TYPE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification will be sent whenever invalid
|
|
configuration detected by XML"
|
|
::= { ciscoLwappSysMIBNotifs 1 }
|
|
|
|
ciscoLwappNoVlanConfigured NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
cldcClientAccessVLAN,
|
|
cldcClientMacAddress
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification will be sent whenever wired client
|
|
tries to associate without interface for specified vlan"
|
|
::= { ciscoLwappSysMIBNotifs 2 }
|
|
|
|
ciscoLwappStrongPwdCheck NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
clsSecStrongPwdManagementUser,
|
|
clsSecStrongPwdCheckType,
|
|
clsSecStrongPwdCheckOption
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification will be sent whenever the management
|
|
user enables/disables the strong password rules."
|
|
::= { ciscoLwappSysMIBNotifs 3 }
|
|
|
|
ciscoLwappSysCpuUsageHigh NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
clsSysCurrentCpuUsage,
|
|
clsSysAlarmSet
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When a WLC detects its CPU usage is higher than the
|
|
threshold configured in clsSysControllerCpuUsageThreshold,
|
|
this notification is generated with clsSysAlarmSet set
|
|
to true. When its CPU usage falls below the threshold
|
|
lately, this notification is generated with
|
|
clsSysAlarmSet set to false."
|
|
::= { ciscoLwappSysMIBNotifs 4 }
|
|
|
|
ciscoLwappSysMemoryUsageHigh NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
clsSysCurrentMemoryUsage,
|
|
clsSysAlarmSet
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When a WLC detects its memory usage is higher than the
|
|
threshold configured in clsSysControllerMemoryUsageThreshold,
|
|
this notification is generated with clsSysAlarmSet set
|
|
to true. When its memory usage falls below the threshold
|
|
lately, this notification is generated with
|
|
clsSysAlarmSet set to false."
|
|
::= { ciscoLwappSysMIBNotifs 5 }
|
|
|
|
ciscoLwappMaxRFIDTagsReached NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
clsMaxRFIDTagsTrapThreshold,
|
|
clsMaxRFIDTagsCount
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is generated when the number of
|
|
RFID tags on the controller exceeds the limit defined by
|
|
clsMaxRFIDTagsTrapThreshold."
|
|
::= { ciscoLwappSysMIBNotifs 6 }
|
|
|
|
ciscoLwappMaxClientsReached NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
clsMaxClientsTrapThreshold,
|
|
clsMaxClientsCount
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is generated when the number of
|
|
clients on the controller exceeds the limit defined by
|
|
clsMaxClientsTrapThreshold."
|
|
::= { ciscoLwappSysMIBNotifs 7 }
|
|
|
|
ciscoLwappNMHeartBeat NOTIFICATION-TYPE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification will be sent when Network Mamager
|
|
Heart Beat Enable."
|
|
::= { ciscoLwappSysMIBNotifs 8 }
|
|
|
|
-- ********************************************************************
|
|
-- * Individual CPU Usage
|
|
-- ********************************************************************
|
|
|
|
clsAllCpuUsage OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the CPU usage string."
|
|
::= { clsCpuInfo 1 }
|
|
-- ********************************************************************
|
|
|
|
ciscoLwappSysMIBCompliances OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBConform 1 }
|
|
|
|
ciscoLwappSysMIBGroups OBJECT IDENTIFIER
|
|
::= { ciscoLwappSysMIBConform 2 }
|
|
|
|
|
|
-- ********************************************************************
|
|
-- * Units of conformance
|
|
-- ********************************************************************
|
|
|
|
ciscoLwappSysMIBCompliance MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for the SNMP entities that
|
|
implement the ciscoLwappSysMIB module."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS { ciscoLwappSysConfigGroup }
|
|
::= { ciscoLwappSysMIBCompliances 1 }
|
|
|
|
ciscoLwappSysMIBComplianceRev1 MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for the SNMP entities that
|
|
implement the ciscoLwappSysMIB module."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS { ciscoLwappSysConfigGroup }
|
|
|
|
GROUP ciscoLwappSysConfigFileEncryptionGroup
|
|
DESCRIPTION
|
|
"This group is mandatory only for platforms which support Config
|
|
Encryption."
|
|
|
|
GROUP ciscoLwappSysTransferOperationConfigGroup
|
|
DESCRIPTION
|
|
"This group is mandatory only for platforms which support
|
|
configuration of Transfer operation."
|
|
::= { ciscoLwappSysMIBCompliances 2 }
|
|
|
|
ciscoLwappSysMIBComplianceRev2 MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for the SNMP entities that
|
|
implement the ciscoLwappSysMIB module. This deprecates
|
|
ciscoLwappSysMIBComplianceRev1."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
ciscoLwappSysConfigGroup,
|
|
ciscoLwappSysPortConfigGroup,
|
|
ciscoLwappSysSecurityConfigGroup,
|
|
ciscoLwappSysIgmpConfigGroup,
|
|
ciscoLwappSysSecNotifObjsGroup,
|
|
ciscoLwappSysNotifsGroup,
|
|
ciscoLwappSysNotifControlGroup,
|
|
ciscoLwappSysConfigGroupVer1
|
|
}
|
|
|
|
GROUP ciscoLwappSysConfigFileEncryptionGroup
|
|
DESCRIPTION
|
|
"This group is mandatory only for platforms which support Config
|
|
Encryption."
|
|
|
|
GROUP ciscoLwappSysTransferOperationConfigGroup
|
|
DESCRIPTION
|
|
"This group is mandatory only for platforms which support
|
|
configuration of Transfer operation."
|
|
::= { ciscoLwappSysMIBCompliances 3 }
|
|
|
|
ciscoLwappSysMIBComplianceRev3 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for the SNMP entities that
|
|
implement the ciscoLwappSysMIB module. This deprecates
|
|
ciscoLwappSysMIBComplianceRev2."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
ciscoLwappSysConfigGroup,
|
|
ciscoLwappSysPortConfigGroup,
|
|
ciscoLwappSysSecurityConfigGroup,
|
|
ciscoLwappSysIgmpConfigGroup,
|
|
ciscoLwappSysSecNotifObjsGroup,
|
|
ciscoLwappSysNotifsGroup,
|
|
ciscoLwappSysNotifControlGroup,
|
|
ciscoLwappSysConfigGroupVer1,
|
|
ciscoLwappSysConfigGroupSup1,
|
|
ciscoLwappSysMldConfigGroup,
|
|
ciscoLwappSysConfigStatsGroup,
|
|
ciscoLwappSysAlarmObjectGroup,
|
|
ciscoLwappSysThresholdGroup,
|
|
ciscoLwappSysHeartBeatGroup,
|
|
ciscoLwappSysInfoGroup
|
|
}
|
|
|
|
GROUP ciscoLwappSysConfigFileEncryptionGroup
|
|
DESCRIPTION
|
|
"This group is mandatory only for platforms which support Config
|
|
Encryption."
|
|
|
|
GROUP ciscoLwappSysTransferOperationConfigGroup
|
|
DESCRIPTION
|
|
"This group is mandatory only for platforms which support
|
|
configuration of Transfer operation."
|
|
::= { ciscoLwappSysMIBCompliances 4 }
|
|
|
|
ciscoLwappSysConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsDot3BridgeEnabled,
|
|
clsDownloadFileType,
|
|
clsDownloadCertificateKey,
|
|
clsUploadFileType,
|
|
clsUploadPacUsername,
|
|
clsUploadPacPassword,
|
|
clsUploadPacValidity,
|
|
cLSysBroadcastForwardingEnabled,
|
|
clsConfigProductBranchVersion,
|
|
clsConfigDhcpProxyEnabled,
|
|
clsCrashSystem
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the system wide
|
|
configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 1 }
|
|
|
|
ciscoLwappSysConfigFileEncryptionGroup OBJECT-GROUP
|
|
OBJECTS { clsTransferConfigFileEncryptionKey }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the System encryption configuration on
|
|
the controller."
|
|
::= { ciscoLwappSysMIBGroups 2 }
|
|
|
|
ciscoLwappSysTransferOperationConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsTransferServerAddressType,
|
|
clsTransferServerAddress,
|
|
clsTransferPath,
|
|
clsTransferFilename,
|
|
clsTransferFtpUsername,
|
|
clsTransferFtpPassword,
|
|
clsTransferFtpPortNum,
|
|
clsTransferTftpMaxRetries,
|
|
clsTransferTftpTimeout,
|
|
clsTransferStart,
|
|
clsTransferStatus,
|
|
clsTransferStatusString,
|
|
clsTransferConfigFileEncryption
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object represents the System Transfer operation
|
|
configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 3 }
|
|
|
|
ciscoLwappSysPortConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsPortModePhysicalMode,
|
|
clsPortModePhysicalStatus,
|
|
clsPortModeSfpType,
|
|
clsPortUpDownCount
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the system wide
|
|
configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 4 }
|
|
|
|
ciscoLwappSysSecurityConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsSecStrongPwdCaseCheck,
|
|
clsSecStrongPwdConsecutiveCheck,
|
|
clsSecStrongPwdDefaultCheck,
|
|
clsSecStrongPwdAsUserNameCheck
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the system security
|
|
configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 5 }
|
|
|
|
ciscoLwappSysIgmpConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cLSysMulticastIGMPSnoopingEnabled,
|
|
cLSysMulticastIGMPSnoopingTimeout,
|
|
cLSysMulticastIGMPQueryInterval
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the IGMP multicast
|
|
configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 6 }
|
|
|
|
ciscoLwappSysSecNotifObjsGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsSecStrongPwdManagementUser,
|
|
clsSecStrongPwdCheckType,
|
|
clsSecStrongPwdCheckOption,
|
|
clsSysAlarmSet
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the information carried
|
|
by the security related notifications sent by the agent to a
|
|
network management station."
|
|
::= { ciscoLwappSysMIBGroups 7 }
|
|
|
|
ciscoLwappSysNotifsGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS {
|
|
ciscoLwappSysInvalidXmlConfig,
|
|
ciscoLwappNoVlanConfigured,
|
|
ciscoLwappStrongPwdCheck,
|
|
ciscoLwappSysCpuUsageHigh,
|
|
ciscoLwappSysMemoryUsageHigh,
|
|
ciscoLwappMaxRFIDTagsReached,
|
|
ciscoLwappMaxClientsReached,
|
|
ciscoLwappNMHeartBeat
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the system config related
|
|
notifications sent by the agent to a network management
|
|
station."
|
|
::= { ciscoLwappSysMIBGroups 8 }
|
|
|
|
ciscoLwappSysNotifControlGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsSecStrongPwdCheckTrapEnabled,
|
|
clsMaxClientsTrapEnabled,
|
|
clsMaxRFIDTagsTrapEnabled
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the flags to control the
|
|
generation of notification."
|
|
::= { ciscoLwappSysMIBGroups 9 }
|
|
|
|
ciscoLwappSysConfigGroupVer1 OBJECT-GROUP
|
|
OBJECTS {
|
|
cLSysBroadcastForwardingEnabled,
|
|
cLSysLagModeEnabled,
|
|
clsConfigProductBranchVersion,
|
|
clsConfigDhcpProxyEnabled,
|
|
clsCoreDumpTransferEnable,
|
|
clsCoreDumpTransferMode,
|
|
clsCoreDumpServerIPAddressType,
|
|
clsCoreDumpServerIPAddress,
|
|
clsCoreDumpFileName,
|
|
clsCoreDumpUserName,
|
|
clsCoreDumpPassword,
|
|
clsConfigMulticastEnabled,
|
|
cLSysLagModeInTransition,
|
|
clsEmergencyImageVersion,
|
|
clsAllCpuUsage
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the system wide
|
|
configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 10 }
|
|
|
|
ciscoLwappSysConfigGroupSup1 OBJECT-GROUP
|
|
OBJECTS {
|
|
clsTimeZone,
|
|
clsTimeZoneDescription,
|
|
cLSysLogAddressType,
|
|
cLSysLogAddress,
|
|
cLSysLogHostRowStatus,
|
|
cLSysArpUnicastEnabled,
|
|
clsMaxClientsTrapThreshold,
|
|
clsMaxRFIDTagsTrapThreshold
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represents the
|
|
timzone and syslog configuration on the
|
|
controller."
|
|
::= { ciscoLwappSysMIBGroups 11 }
|
|
|
|
ciscoLwappSysMldConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cLSysMulticastMLDSnoopingEnabled,
|
|
cLSysMulticastMLDSnoopingTimeout,
|
|
cLSysMulticastMLDQueryInterval
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represent the MLD multicast
|
|
configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 12 }
|
|
|
|
ciscoLwappSysConfigStatsGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsSysRealtimeStatsTimer,
|
|
clsSysNormalStatsTimer,
|
|
clsSysStatsSamplingInterval,
|
|
clsSysStatsAverageInterval
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represents the
|
|
statistics intervals configuration
|
|
on the controller."
|
|
::= { ciscoLwappSysMIBGroups 13 }
|
|
|
|
ciscoLwappSysAlarmObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsAlarmHoldTime,
|
|
clsAlarmTrapRetransmitInterval
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represents the
|
|
alarm objetcs configurations on the controller."
|
|
::= { ciscoLwappSysMIBGroups 14 }
|
|
|
|
ciscoLwappSysThresholdGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsSysControllerCpuUsageThreshold,
|
|
clsSysControllerMemoryUsageThreshold,
|
|
clsSysApCpuUsageThreshold,
|
|
clsSysApMemoryUsageThreshold
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represents the
|
|
Threshold configuration on the controller."
|
|
::= { ciscoLwappSysMIBGroups 15 }
|
|
|
|
ciscoLwappSysHeartBeatGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsNMHeartBeatEnable,
|
|
clsNMHeartBeatInterval
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects represents the
|
|
heart beat configurations on the controller."
|
|
::= { ciscoLwappSysMIBGroups 16 }
|
|
|
|
ciscoLwappSysInfoGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clsSysFlashSize,
|
|
clsSysMemoryType,
|
|
clsSysMaxClients,
|
|
clsSysApConnectCount,
|
|
clsSysNetId,
|
|
clsSysCurrentMemoryUsage,
|
|
clsSysAverageMemoryUsage,
|
|
clsSysCurrentCpuUsage,
|
|
clsSysAverageCpuUsage,
|
|
clsSysCpuType,
|
|
clsMaxRFIDTagsCount,
|
|
clsMaxClientsCount
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group of object represents the
|
|
system information of the controller."
|
|
::= { ciscoLwappSysMIBGroups 17 }
|
|
|
|
END
|
|
|
|
|
|
|