clones/librenms
1
0
Fork 0
mirror of https://github.com/librenms/librenms.git synced 2024-09-22 02:48:37 +00:00
Code Issues Packages Projects Releases Wiki Activity
609ded49fa
librenms/mibs/PW-STD-MIB
Adam Amstrong 8c83b6a3c7 update foundry mibs 
git-svn-id: http://www.observium.org/svn/observer/trunk@3250 61d68cd4-352d-0410-923a-c4978735b2b8
2012-05-29 13:08:01 +00:00

2364 lines
85 KiB
Plaintext
Raw Blame History

PW-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE,
Integer32, Unsigned32, Counter32, Counter64, TimeTicks
FROM SNMPv2-SMI -- [RFC2578]
pwe3
FROM FOUNDRY-SN-ROOT-MIB
snAgGblTrapMessage
FROM FOUNDRY-SN-AGENT-MIB -- [snagent.mib]
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580]
TruthValue, RowStatus, StorageType,
TimeStamp, TEXTUAL-CONVENTION
FROM SNMPv2-TC -- [RFC2579]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
InterfaceIndexOrZero
FROM IF-MIB -- [RFC2863]
InetAddressType, InetAddress
FROM INET-ADDRESS-MIB -- [RFC4001]
PerfCurrentCount, PerfIntervalCount
FROM PerfHist-TC-MIB -- [RFC3593]
HCPerfCurrentCount, HCPerfIntervalCount, HCPerfTimeElapsed,
HCPerfValidIntervals
FROM HC-PerfHist-TC-MIB -- [RFC3705]
PwIndexType, PwIndexOrZeroType, PwGroupID, PwIDType,
PwOperStatusTC, PwAttachmentIdentifierType, PwCwStatusTC,
PwStatus, PwFragSize, PwFragStatus
FROM PW-TC-STD-MIB -- [PWTC]
-- RFC Editor: Please replace [PWTC] with RFC number and remove this
-- note.
IANAPwTypeTC, IANAPwPsnTypeTC, IANAPwCapabilities
FROM IANA-PWE3-MIB -- Reference will be added
-- When IANA will create the
-- MIB module
;
pwStdMIB MODULE-IDENTITY
LAST-UPDATED "200705311200Z" -- 31 May 2007 12:00:00 GMT
ORGANIZATION "Pseudo Wire Edge-to-Edge Emulation (PWE3) Working
Group"
CONTACT-INFO
"
David Zelig
E-mail: davidz@corrigent.com
Thomas D. Nadeau
Email: tnadeau@cisco.com
The PWE3 Working Group (email distribution pwe3@ietf.org,
http://www.ietf.org/html.charters/pwe3-charter.html)
"
DESCRIPTION
"This MIB module contains managed object definitions for
pseudo-wire operation as in Bryant, S. and P. Pate, 'Pseudo
Wire Emulation Edge-to-Edge (PWE3) Architecture' [RFC3985],
Martini, L., et al, 'Pseudowire Setup and Maintenance Using
the Label Distribution Protocol (LDP)' [RFC4447], and
Townsley, M., et al, 'Layer Two Tunneling Protocol
(Version 3)' [RFC3931].
This MIB module enables the use of any underlying packet
switched network (PSN). MIB nodules that will support
PW operations over specific PSN types are defined in
separate memos.
The indexes for this MIB module are also used to index the
PSN-specific tables and the PW-specific tables. The PW Type
dictates which PW-specific MIB module to use.
Copyright (C) The IETF Trust (2007). This version
of this MIB module is part of RFC XXX;
For full legal notices see the RFC itself or
http://www.ietf.org/copyrights/ianamib.html
-- RFC Ed.: replace XXX with actual RFC number & remove this note
"
-- Revision history.
REVISION
"200705311200Z" -- 31 May 2007 12:00:00 GMT
DESCRIPTION "Initial version published as part of RFC YYYY."
-- RFC Editor: please replace YYYY with IANA assigned value, and
-- delete this note.
::= { pwe3 2 }
-- ::= { transmission ZZZZ }
-- RFC Editor: please replace ZZZZ with IANA assigned value, and
-- delete this note.
-- Top-level components of this MIB.
-- Notifications
pwNotifications OBJECT IDENTIFIER
::= { pwStdMIB 0 }
-- Tables, Scalars
pwObjects OBJECT IDENTIFIER
::= { pwStdMIB 1 }
-- Conformance
pwConformance OBJECT IDENTIFIER
::= { pwStdMIB 2 }
-- Foundry Proprietary extension
FdryPwServiceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"MPLS pseudo-wire service types."
SYNTAX INTEGER{
vll(1),
vllLocal(2),
vpls(3)
}
-- PW Virtual Connection Table
pwIndexNext OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to be used
for pwIndex when creating entries in the
pwTable. The value 0 indicates that no
unassigned entries are available. To obtain the
value of pwIndex for a new entry in the
pwTable, the manager issues a management
protocol retrieval operation. The agent will determine
through its local policy when this index value will be made
available for reuse."
::= { pwObjects 1 }
pwTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies information for configuring and
status monitoring which are common to all service types
and PSN types."
::= { pwObjects 2 }
pwEntry OBJECT-TYPE
SYNTAX PwEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents a pseudo-wire (PW) virtual
connection across a packet network. It is indexed by
pwIndex, which uniquely identifies a singular
connection.
A row can be created by an operator command from a
management plan of a PE, by signaling or due to autodiscovery
process. Operator's command can be issued via non SNMP
application; in such case a row will be created implicitly
by the agent.
The read-create objects in this tables are divided into
three categories:
1) Objects that MUST NOT be changed after row activation.
These are objects that define basic properties of the
PW (for example type, destination, etc.).
2) Objects that MAY be changed when the PW is
defined as not active. A change of these objects involves
re-signaling of the PW or it might be traffic affecting.
PW not active is defined as one of the following
conditions:
a) The pwRowStatus is notInService(2).
b) The pwRowStatus is notReady(3).
c) The pwAdminStatus is down(2).
If the operator needs to change one of the values for an
active row, the operator can either set the pwRowStatus to
notInService(2) or set pwAdminStatus to down(2).
Signaling (or traffic) is initiated again upon setting
the pwRowStatus to active(1) or setting the pwAdminStatus
to up(1) or testing(3) respectively.
3) Objects that MAY be changed at any time.
By default, all the read-create objects MUST NOT be
changed after row activation, unless specifically indicated
in the individual object description.
Manual entries in this table SHOULD be preserved after a
re-boot, the agent MUST ensure the integrity of those
entries. If the set of entires of a specific row are found to
be non consistent after reboot, the PW pwOperStatus MUST be
declared as notPresent(5).
"
INDEX { pwIndex }
::= { pwTable 1 }
PwEntry ::= SEQUENCE {
pwIndex PwIndexType,
pwType IANAPwTypeTC,
pwOwner INTEGER,
pwPsnType IANAPwPsnTypeTC,
pwSetUpPriority Integer32,
pwHoldingPriority Integer32,
pwPeerAddrType InetAddressType,
pwPeerAddr InetAddress,
pwAttachedPwIndex PwIndexOrZeroType,
pwIfIndex InterfaceIndexOrZero,
pwID PwIDType,
pwLocalGroupID PwGroupID,
pwGroupAttachmentID PwAttachmentIdentifierType,
pwLocalAttachmentID PwAttachmentIdentifierType,
pwPeerAttachmentID PwAttachmentIdentifierType,
pwCwPreference TruthValue,
pwLocalIfMtu Unsigned32,
pwLocalIfString TruthValue,
pwLocalCapabAdvert IANAPwCapabilities,
pwRemoteGroupID PwGroupID,
pwCwStatus PwCwStatusTC,
pwRemoteIfMtu Unsigned32,
pwRemoteIfString SnmpAdminString,
pwRemoteCapabilities IANAPwCapabilities,
pwFragmentCfgSize PwFragSize,
pwRmtFragCapability PwFragStatus,
pwFcsRetentionCfg INTEGER,
pwFcsRetentionStatus BITS,
pwOutboundLabel Unsigned32,
pwInboundLabel Unsigned32,
pwName SnmpAdminString,
pwDescr SnmpAdminString,
pwCreateTime TimeStamp,
pwUpTime TimeTicks,
pwLastChange TimeTicks,
pwAdminStatus INTEGER,
pwOperStatus PwOperStatusTC,
pwLocalStatus PwStatus,
pwRemoteStatusCapable INTEGER,
pwRemoteStatus PwStatus,
pwTimeElapsed HCPerfTimeElapsed,
pwValidIntervals HCPerfValidIntervals,
pwRowStatus RowStatus,
pwStorageType StorageType,
pwOamEnable TruthValue
}
pwIndex OBJECT-TYPE
SYNTAX PwIndexType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique index for the conceptual row identifying a PW within
this table."
::= { pwEntry 1 }
pwType OBJECT-TYPE
SYNTAX IANAPwTypeTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value indicates the emulated service to be carried over
this PW.
"
::= { pwEntry 2 }
pwOwner OBJECT-TYPE
SYNTAX INTEGER {
manual (1),
pwIdFecSignaling (2), -- PW signaling with PW ID FEC
genFecSignaling (3), -- Generalized attachment FEC
l2tpControlProtocol (4),
other (5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is set by the operator to indicate the protocol
responsible for establishing this PW.
'manual' is used in all cases where no maintenance
protocol (PW signaling) is used to set-up the PW, i.e.
require configuration of entries in the PW tables including
PW labels, etc.
'pwIdFecSignaling' is used in case of signaling with the
Pwid FEC element with LDP signaling.
'genFecSignaling' is used in case of LDP signaling with
the generalized FEC.
'l2tpControlProtocol' indicates the use of L2TP
control protocol.
'other' is used for other types of signaling."
::= { pwEntry 3 }
pwPsnType OBJECT-TYPE
SYNTAX IANAPwPsnTypeTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is set by the operator to indicate the PSN type.
Based on this object, the relevant PSN table's entry is
created in the PSN specific MIB modules.
"
::= { pwEntry 4 }
pwSetUpPriority OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines the relative priority of the PW
during set-up in a lowest-to-highest fashion, where 0
is the highest priority. PWs with the same priority
are treated with equal priority. PW that have not yet
succeeded to set-up will report 'dormant' in the
pwOperStatus.
This value is significant if there are competing resources
among PWs and the implementation support this feature.
Equal priority handling with competing resources is
implementation specific.
This object MAY be changed at any time."
DEFVAL { 0 }
::= { pwEntry 5 }
pwHoldingPriority OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines the relative holding priority of the
PW in a lowest-to-highest fashion, where 0 is the highest
priority. PWs with the same priority are treated equally.
This value is significant if there are competing resources
among PWs and the implementation support this feature.
Equal priority handling with competing resources is
implementation specific.
This object MAY be changed only if the PW is not active."
DEFVAL { 0 }
::= { pwEntry 6 }
pwPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes the address type of the peer node. It should be
set to 'unknown' if PE/PW maintenance protocol is not used
and the address is unknown."
DEFVAL { ipv4 }
::= { pwEntry 8 }
pwPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object contains the value of the peer node address
of the PW/PE maintenance protocol entity. This object
SHOULD contain a value of all zeroes if not applicable
(pwPeerAddrType is 'unknown')."
::= { pwEntry 9 }
pwAttachedPwIndex OBJECT-TYPE
SYNTAX PwIndexOrZeroType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the PW is attached to another PW instead of a local
native service, this item indicates the pwIndex of the
attached PW. Otherwise, this object MUST
be set to zero. Attachement to another PW will have no
PW specific entry in any of the service MIB modules. "
DEFVAL { 0 }
::= { pwEntry 10 }
pwIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the ifIndex of the PW if the PW is
represented in the ifTable. Otherwise, it MUST be set
to zero."
DEFVAL { 0 }
::= { pwEntry 11 }
pwID OBJECT-TYPE
SYNTAX PwIDType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Pseudo Wire identifier.
If the pwOwner object is 'pwIdFecSignaling' or
'l2tpControlProtocol', then this object is signaled in the
outgoing PW ID field within the 'Virtual Circuit FEC
Element'. For other values of pwOwner, this object is not
signaled and it MAY be set to zero.
For implementations that support the pwIndexMappingTable,
a non-zero value is RECOMMENDED, even if this
identifier is not signaled. This is so that reverse
mappings can be provided by pwIndexMappingTable and
pwPeerMappingTable. It is therefore RECOMMENDED that the
value of this pwID be unique (or if pwPeerAddrType is not
'unknown', at least [pwType,pwID,pwPeerAddrType,pwPeerAddr]
is unique.)"
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 12 }
pwLocalGroupID OBJECT-TYPE
SYNTAX PwGroupID
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Used in the Group ID field sent to the peer PWES
within the maintenance protocol used for PW setup.
It SHOULD be set to zero if maintenance protcol is
not used."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 13 }
pwGroupAttachmentID OBJECT-TYPE
SYNTAX PwAttachmentIdentifierType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is an octet string representing the attachment
group identifier (AGI) that this PW belongs too, which
typically identifies the VPN ID.
Applicable if pwOwner equal 'genFecSignaling'."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 14 }
pwLocalAttachmentID OBJECT-TYPE
SYNTAX PwAttachmentIdentifierType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is an octet string representing the local
forwarder attachment individual identifier (AII) to be
used by this PW. It is used as the SAII for outgoing
signaling messages and the TAII in the incoming messages
from the peer.
Applicable if pwOwner equal 'genFecSignaling'."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 15 }
pwPeerAttachmentID OBJECT-TYPE
SYNTAX PwAttachmentIdentifierType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is an octet string representing the peer
forwarder attachment individual identifier (AII) to be
used by this PW. It is used as the TAII for outgoing
signaling messages and the SAII in the incoming messages
from the peer.
Applicable if pwOwner equal 'genFecSignaling'."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 16 }
pwCwPreference OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines if the control word will be sent with each packet
by the local node. Some PW types mandate the use of a
control word, and in such cases the value configured for
this object has no effect on the existence of the control
word.
This object MAY be changed only if the PW is not active."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol.', RFC 4447."
DEFVAL { false }
::= { pwEntry 17 }
pwLocalIfMtu OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If not equal to zero, the optional IfMtu object in the
signaling protocol will be sent with this value, which
represents the locally-supported MTU size over the
interface (or the virtual interface) associated with the
PW.
This object MAY be changed only if the PW is not active."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
DEFVAL { 0 }
::= { pwEntry 18 }
pwLocalIfString OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A PW MAY be associated to an interface (or a virtual
interface) in the ifTable of the node as part of the
service configuration. This object defines if the
maintenance protocol will send the interface's name
(ifAlias) as appears in the ifTable. If set to false,
the optional element will not be sent.
This object MAY be changed only if the PW is not active."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447, section 5.5."
DEFVAL { false }
::= { pwEntry 19 }
pwLocalCapabAdvert OBJECT-TYPE
SYNTAX IANAPwCapabilities
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If maintenance protcol is used, it indicates the
capabilities the local node will advertize to the
peer. The operator MAY selectively assign partial set
of capabilities. In case of manual configuration of the PW,
the operator SHOULD set non conflicting options (for example
only a single type of OAM) out of the available options
in the implementation.
It is possible to change the value of this object when the
PW is not active. The agent MUST reject any attempt to set
a capability that is not supported.
The default value MUST be the full set of local node
capabilities."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 20 }
pwRemoteGroupID OBJECT-TYPE
SYNTAX PwGroupID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is obtained from the Group ID field as
received via the maintenance protocol used for PW setup.
Value zero will be reported if not used.
Value of 0xFFFFFFFF shall be used if the object is yet to be
defined by the PW maintenance protocol."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 21 }
pwCwStatus OBJECT-TYPE
SYNTAX PwCwStatusTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If signaling is used for PW establishment, this object
indicates the status of the control word negotiation,
and in both; signaling or manual configuration it indicates
if CW is to be present for this PW."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 22 }
pwRemoteIfMtu OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote interface MTU as (optionally) received from the
remote node via the maintenance protocol. The object SHOULD
report zero if MTU is not available."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 23 }
pwRemoteIfString OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..80))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the interface description string as received by
the maintenance protocol. It MUST be a NULL string if
maintenance protocol is not used or the value is not known
yet."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447, section 5.5."
::= { pwEntry 24 }
pwRemoteCapabilities OBJECT-TYPE
SYNTAX IANAPwCapabilities
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the capabilities as recieved from the peer."
REFERENCE
"Martini, et al, 'Pseudowire Setup and Maintenance using
the Label Distribution Protocol', RFC 4447."
::= { pwEntry 25 }
pwFragmentCfgSize OBJECT-TYPE
SYNTAX PwFragSize
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If set to a value other than zero, indicates that
fragmentation is desired for this PW.
This object MAY be changed only if the PW is not active."
REFERENCE
"Malis A., Townsley M., 'PWE3 Fragmentation and Reassembly',
RFC 4623."
DEFVAL { 0 } -- i.e. fragmentation not desired
::= { pwEntry 26 }
pwRmtFragCapability OBJECT-TYPE
SYNTAX PwFragStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the fragmentation based on the local
configuration and the peer capabilities as recieved from
the peer when control protocol is used."
REFERENCE
"Malis A., Townsley M., 'PWE3 Fragmentation and Reassembly',
RFC 4623."
::= { pwEntry 27 }
pwFcsRetentionCfg OBJECT-TYPE
SYNTAX INTEGER {
fcsRetentionDisable (1),
fcsRetentionEnable (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The local configuration of FCS retention for this PW. FCS
retention can be configured for PW types HDLC, PPP and
Ethernet only. If the implementation does not support
FCS retention, error MUST be reported in pwFcsRetentionStatus.
This object MAY be changed only if the PW is not active."
REFERENCE
"Malis A., et al., 'PWE3 Frame Check Sequence Retention',
RFC 4720."
DEFVAL { fcsRetentionDisable }
::= { pwEntry 28 }
pwFcsRetentionStatus OBJECT-TYPE
SYNTAX BITS {
remoteIndicationUnknown (0),
remoteRequestFcsRetention (1),
fcsRetentionEnabled (2),
fcsRetentionDisabled (3),
localFcsRetentionCfgErr (4),
fcsRetentionFcsSizeMismatch (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the FCS retention negotiation process based on
local configuration and the remote advertisement.
remoteIndicationUnknown - set if a FEC has not been received
from the remote.
remoteRequestFcsRetention - indicates that the peer has
requested for FCS retention. FCS retention will be used if
the local node is capable and configured to use it for this
PW.
fcsRetentionEnabled - FCS retention is enabled (both peers
were configured for FCS retention for signaled PW, or the
local node is configured and capable for FCS retention for
manually assigned PW).
fcsRetentionDisabled - FCS retention is disabled (not
configured locally or not advertised by the peer).
localFcsRetentionCfgErr - Set if the local node has been
configured for FCS retention but is not capable to support
it.
fcsRetentionFcsSizeMismatch - Set if there is an FCS size
mismatch between the local and the peer node.
"
REFERENCE
"Malis A., et al., 'PWE3 Frame Check Sequence Retention',
RFC 4720"
::= { pwEntry 29 }
pwOutboundLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The PW label used in the outbound direction (i.e. toward
the PSN). It might be set manually if pwOwner is 'manual',
otherwise setting done automatically.
For MPLS, MPLS over IP or MPLS over GRE PSN, it represents
the 20 bits of PW tag, for L2TP it represents the 32 bits
Session ID and for IP PSN it represents the destination
UDP port number.
If the label is not yet known (signaling in process), the
object SHOULD return a value of 0xFFFFFFFF.
For manual configuration, this object MAY be changed only
if the PW is not active."
::= { pwEntry 30 }
pwInboundLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The PW label used in the inbound direction (i.e. packets
received from the PSN). It may be set manually if pwOwner
is 'manual',otherwise setting done automatically.
For MPLS, MPLS over IP or MPLS over GRE PSN, it represents
the 20 bits of PW tag, for L2TP it represents the 32 bits
Session ID and for IP PSN it represents the source
UDP port number.
If the label is not yet known (signaling in process), the
object SHOULD return a value of 0xFFFFFFFF.
For manual configuration, this object MAY be changed only
if the PW is not active."
::= { pwEntry 31 }
pwName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The canonical name assigned to the PW. This object MAY be
changed at any time."
::= { pwEntry 32 }
pwDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A textual string containing information about the PW.
If there is no description this object contains a zero
length string. This object MAY be changed at any time."
::= { pwEntry 33 }
pwCreateTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this PW was created."
::= { pwEntry 34 }
pwUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the time since last change of pwOperStatus to
Up(1)."
::= { pwEntry 35 }
pwLastChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time the PW entered
its current operational state. If the current state was
entered prior to the last re-initialization of the local
network management subsystem, then this object contains a
zero value."
::= { pwEntry 36 }
pwAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1), -- ready to pass packets
down(2),
testing(3) -- in a test mode
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The desired operational status of this PW. This object MAY
be set at any time."
::= { pwEntry 37 }
pwOperStatus OBJECT-TYPE
SYNTAX PwOperStatusTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the operational status of the PW, it
does not reflect the status of the CE bound interface.
It is set to down only if pwNotForwarding,
psnFacingPwRxFault, or psnFacingPwTxFault indications are
set in pwLocalStatus or pwRemoteStatus.
It indicates 'lowerLayerDown' if the only reason for
not being in the 'up' state is either outer tunnel
or physical layer down of the network side is in the down
state.
All other states are declared based on the description in
the textual convention.
"
::= { pwEntry 38 }
pwLocalStatus OBJECT-TYPE
SYNTAX PwStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of the PW in the local node.
The various indications in this object SHOULD be
available independent of the ability of the local node to
advertise them or the remote node to accept these status
indications through the control protocol.
"
::= { pwEntry 39 }
pwRemoteStatusCapable OBJECT-TYPE
SYNTAX INTEGER {
notApplicable (1),
notYetKnown (2),
remoteCapable (3),
remoteNotCapable (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the remote node capability to advertise the
PW status notification.
notAppicable SHOULD be reported for manually set PW, or
if the local node is not capable of accepting the status
notification object.
notYetKnown SHOULD be reported if the signaling protocol
has not yet finished the process of capability
determination.
remoteCapable and remoteNotcapable SHOULD be reported
based on the initial signaling exchange that has
determined the remote node capability.
"
::= { pwEntry 40 }
pwRemoteStatus OBJECT-TYPE
SYNTAX PwStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of the PW as was advertised by the
remote. If the remote is not capable of advertising the
status object, or the local node is not able to accept
the status object through signaling, then the applicable
bit is 'pwNotForwarding' which is set if the remote has
sent label release or label withdraw for this PW.
"
::= { pwEntry 41 }
pwTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds, including partial seconds,
that have elapsed since the beginning of the current
interval measurement period."
::= { pwEntry 42 }
pwValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of previous 15-minute intervals
for which data was collected."
::= { pwEntry 43 }
pwRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row.
This object MAY be changed at any time."
::= { pwEntry 44 }
pwStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object."
DEFVAL { nonVolatile }
::= { pwEntry 45 }
pwOamEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates if OAM is enabled for this
PW. It MAY be changed at any time."
DEFVAL { true }
::= { pwEntry 46 }
-- End of PW Virtual Connection Table
-- PW Performance Table.
pwPerfCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides per-PW performance information for
the current interval."
::= { pwObjects 3 }
pwPerfCurrentEntry OBJECT-TYPE
SYNTAX PwPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for
every PW."
INDEX { pwIndex }
::= { pwPerfCurrentTable 1 }
PwPerfCurrentEntry ::= SEQUENCE {
pwPerfCurrentInHCPackets HCPerfCurrentCount,
pwPerfCurrentInHCBytes HCPerfCurrentCount,
pwPerfCurrentOutHCPackets HCPerfCurrentCount,
pwPerfCurrentOutHCBytes HCPerfCurrentCount,
pwPerfCurrentInPackets PerfCurrentCount,
pwPerfCurrentInBytes PerfCurrentCount,
pwPerfCurrentOutPackets PerfCurrentCount,
pwPerfCurrentOutBytes PerfCurrentCount
}
pwPerfCurrentInHCPackets OBJECT-TYPE
SYNTAX HCPerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of packets received by
the PW (from the PSN) in the current 15-minute interval.
This is the 64 bit version of pwPerfCurrentInPackets,
if pwPerfCurrentInHCPackets is supported according to
the rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 1 }
pwPerfCurrentInHCBytes OBJECT-TYPE
SYNTAX HCPerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of bytes received by the
PW (from the PSN) in the current 15-minute interval.
This is the 64 bit version of pwPerfCurrentInBytes, if
pwPerfCurrentInHCBytes is supported according to the
rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 2 }
pwPerfCurrentOutHCPackets OBJECT-TYPE
SYNTAX HCPerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of packets forwarded by
the PW (to the PSN) in the current 15-minute interval.
This is the 64 bit version of pwPerfCurrentOutPackets,
if pwPerfCurrentOutHCPackets is supported according to
the rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 3 }
pwPerfCurrentOutHCBytes OBJECT-TYPE
SYNTAX HCPerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of bytes forwarded by
the PW (to the PSN) in the current 15-minute interval.
This is the 64 bit version of pwPerfCurrentOutBytes,
if pwPerfCurrentOutHCBytes is supported according to
the rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 4 }
pwPerfCurrentInPackets OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter for number of packets received by the PW (from
the PSN) in the current 15-minute interval.
This is the 32 bit version of pwPerfCurrentInHCPackets,
if pwPerfCurrentInHCPackets is supported according to
the rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 5 }
pwPerfCurrentInBytes OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter for number of bytes received by the
PW (from the PSN) in the current 15-minute interval.
It MUST be equal to the least significant 32 bits of
pwPerfCurrentInHCBytes, if pwPerfCurrentInHCBytes is
supported according to the rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 6 }
pwPerfCurrentOutPackets OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter for number of packets forwarded by
the PW (to the PSN) in the current 15-minute interval.
It MUST be equal to the least significant 32 bits of
pwPerfCurrentOutHCPackets, if
pwPerfCurrentOutHCPackets is supported according to the
rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 7 }
pwPerfCurrentOutBytes OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter for number of bytes forwarded by
the PW (to the PSN) in the current 15-minute interval.
It MUST be equal to the least significant 32 bits of
pwPerfCurrentOutHCBytes, if pwPerfCurrentOutHCBytes is
supported according to the rules spelled out in RFC2863."
::= { pwPerfCurrentEntry 8 }
-- End of PW Perf current Table
-- PW Performance Interval Table.
pwPerfIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides per-PW performance information for
each interval."
::= { pwObjects 4 }
pwPerfIntervalEntry OBJECT-TYPE
SYNTAX PwPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for every
PW."
INDEX { pwIndex, pwPerfIntervalNumber }
::= { pwPerfIntervalTable 1 }
PwPerfIntervalEntry ::= SEQUENCE {
pwPerfIntervalNumber Integer32,
pwPerfIntervalValidData TruthValue,
pwPerfIntervalTimeElapsed HCPerfTimeElapsed,
pwPerfIntervalInHCPackets HCPerfIntervalCount,
pwPerfIntervalInHCBytes HCPerfIntervalCount,
pwPerfIntervalOutHCPackets HCPerfIntervalCount,
pwPerfIntervalOutHCBytes HCPerfIntervalCount,
pwPerfIntervalInPackets PerfIntervalCount,
pwPerfIntervalInBytes PerfIntervalCount,
pwPerfIntervalOutPackets PerfIntervalCount,
pwPerfIntervalOutBytes PerfIntervalCount
}
pwPerfIntervalNumber OBJECT-TYPE
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number N, between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval, and the interval identified
by N is the interval immediately preceding the one
identified by N-1.
The minimum range of N is 1 through 4. The default range
is 1 to 32. The maximum range of N is 1 through 96. "
REFERENCE
"Tesink, K. 'Definitions of Managed Objects for the
SONET/SDH Interface Type', RFC 2558"
::= { pwPerfIntervalEntry 1 }
pwPerfIntervalValidData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval
is valid."
::= { pwPerfIntervalEntry 2 }
pwPerfIntervalTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of this interval in seconds."
::= { pwPerfIntervalEntry 3 }
pwPerfIntervalInHCPackets OBJECT-TYPE
SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of packets received by
the PW (from the PSN) during the interval. This is the 64
bit version of pwPerfIntervalInPackets, if
pwPerfIntervalInHCPackets is supported according to the
rules spelled out in RFC2863."
::= { pwPerfIntervalEntry 4 }
pwPerfIntervalInHCBytes OBJECT-TYPE
SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of bytes received by the
PW (from the PSN) during the interval.
This is the 64 bit version of pwPerfIntervalInBytes, if
pwPerfIntervalInHCBytes is supported according to the
rules spelled out in RFC2863."
::= { pwPerfIntervalEntry 5 }
pwPerfIntervalOutHCPackets OBJECT-TYPE
SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of packets forwarded by
the PW (to the PSN) during the interval.
This is the 64 bit version of pwPerfIntervalOutPackets,
if pwPerfIntervalOutHCPackets is supported according to
the rules spelled out in RFC2863."
::= { pwPerfIntervalEntry 6 }
pwPerfIntervalOutHCBytes OBJECT-TYPE
SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of bytes forwarded by
the PW (to the PSN) during the interval.
This is the 64 bit version of pwPerfIntervalOutBytes,
if pwPerfIntervalOutHCBytes is supported according to
the rules spelled out in RFC2863."
::= { pwPerfIntervalEntry 7 }
pwPerfIntervalInPackets OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the number of packets received
by this PW during the interval.
It MUST be equal to the least significant 32 bits of
pwPerfIntervalInHCPackets if pwPerfIntervalInHCPackets
is supported according to the rules spelled out in
RFC2863."
::= { pwPerfIntervalEntry 8 }
pwPerfIntervalInBytes OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the number of bytes received
by this PW during the interval.
It MUST be equal to the least significant 32 bits of
if pwPerfIntervalInHCBytes is supported according to
the rules spelled out in RFC2863."
::= { pwPerfIntervalEntry 9 }
pwPerfIntervalOutPackets OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the number of packets sent by this
PW during the interval.
It MUST be equal to the least significant 32 bits of
pwPerfIntervalOutHCPackets if
pwPerfIntervalOutHCPackets is supported according to the
rules spelled out in RFC2863."
::= { pwPerfIntervalEntry 10 }
pwPerfIntervalOutBytes OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the number of bytes sent by this
PW during the interval.
It MUST be equal to the least significant 32
bits of pwPerfIntervalOutHCBytes
if pwPerfIntervalOutHCBytes is supported according to
the rules spelled out in RFC2863."
::= { pwPerfIntervalEntry 11 }
-- End of PW Performance Interval Table
-- PW Performance Total Table.
pwPerfTotalTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwPerfTotalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides per-PW Performance information from
PW start time or management application reset.
This table has been obsoleted from draft v.11 and a new
table pwPerf1DayIntervalTable has been introduced. However,
due to better support, pwPerfTotalTable is supported in the
place of pwPerf1DayIntervalTable."
::= { pwObjects 5 }
pwPerfTotalEntry OBJECT-TYPE
SYNTAX PwPerfTotalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for every
PW.
pwPerfTotalDiscontinuityTime indicates the time of the
last discontinuity in any of these objects."
INDEX { pwIndex }
::= { pwPerfTotalTable 1 }
PwPerfTotalEntry ::= SEQUENCE {
pwPerfTotalInHCPackets Counter64,
pwPerfTotalInHCBytes Counter64,
pwPerfTotalOutHCPackets Counter64,
pwPerfTotalOutHCBytes Counter64,
pwPerfTotalInPackets Counter32,
pwPerfTotalInBytes Counter32,
pwPerfTotalOutPackets Counter32,
pwPerfTotalOutBytes Counter32,
pwPerfTotalDiscontinuityTime TimeStamp
}
pwPerfTotalInHCPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for the total number of packets
received by the PW (from the PSN).
This is the 64 bit version of pwPerfTotalInPackets, if
pwPerfTotalInHCPackets is supported according to the
rules spelled out in RFC2863."
::= { pwPerfTotalEntry 1 }
pwPerfTotalInHCBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for the total number of bytes
received by the PW (from the PSN).
This is the 64 bit version of pwPerfTotalInBytes, if
pwPerfTotalInHCBytes is supported according to the
rules spelled out in RFC2863."
::= { pwPerfTotalEntry 2 }
pwPerfTotalOutHCPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for the total number of packets
forwarded by the PW (to the PSN).
This is the 64 bit version of pwPerfTotalOutPackets,
if pwPerfTotalOutHCPackets is supported according to
the rules spelled out in RFC2863."
::= { pwPerfTotalEntry 3 }
pwPerfTotalOutHCBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for the total number of bytes
forwarded by the PW (to the PSN).
This is the 64 bit version of pwPerfTotalOutBytes,
if pwPerfTotalOutHCBytes is supported according to
the rules spelled out in RFC2863."
::= { pwPerfTotalEntry 4 }
pwPerfTotalInPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the total number of packets received
by this PW.
It MUST be equal to the least significant 32 bits of
pwPerfTotalInHCPackets if pwPerfTotalInHCPackets
is supported according to the rules spelled out in
RFC2863."
::= { pwPerfTotalEntry 5 }
pwPerfTotalInBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the total number of bytes received
by this PW.
It MUST be equal to the least significant 32 bits of
if pwPerfTotalInHCBytes is supported according to
the rules spelled out in RFC2863."
::= { pwPerfTotalEntry 6 }
pwPerfTotalOutPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the total number of packets sent by
this PW.
It MUST be equal to the least significant 32 bits of
pwPerfTotalOutHCPackets if pwPerfTotalOutHCPackets
is supported according to the rules spelled out in
RFC2863."
::= { pwPerfTotalEntry 7 }
pwPerfTotalOutBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the total number of bytes sent by
this PW.
It MUST be equal to the least significant 32
bits of pwPerfTotalOutHCBytes
if pwPerfTotalOutHCBytes is supported according to
the rules spelled out in RFC2863."
::= { pwPerfTotalEntry 8 }
pwPerfTotalDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which any one or more of this row Counter32 or
Counter64 suffered a discontinuity. If no such
discontinuities have occurred since the last re-
initialization of the local management subsystem, then
this object contains a zero value."
::= { pwPerfTotalEntry 9 }
-- End of PW Perf Total Table
-- Error counter scalar
pwPerfTotalErrorPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Counter for number of error at the PW processing level,
for example packets received with unknown PW label."
::= { pwObjects 6 }
-- Reverse mapping tables
-- The PW ID mapping table
pwIndexMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwIndexMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table enables the reverse mapping the unique PWid
parameters [peer IP, PW type and PW ID] and the
pwIndex. The table is not applicable for PW created
manually or by using the generalized FEC."
::= { pwObjects 7 }
pwIndexMappingEntry OBJECT-TYPE
SYNTAX PwIndexMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table MUST be created by the agent for
every PW created by the pwTable for which pwOwner
equals pwIdFecSignaling and pwID is not zero.
Implementors need to be aware that if the value of
the pwIndexMappingPeerAddr (an OID) has more than
112 sub-identifiers, then OIDs of column instances
in this table will have more than 128
sub-identifiers and cannot be accessed using SNMPv1,
SNMPv2c, or SNMPv3."
INDEX { pwIndexMappingPwType, pwIndexMappingPwID,
pwIndexMappingPeerAddrType, pwIndexMappingPeerAddr
}
::= { pwIndexMappingTable 1 }
PwIndexMappingEntry ::= SEQUENCE {
pwIndexMappingPwType IANAPwTypeTC,
pwIndexMappingPwID PwIDType,
pwIndexMappingPeerAddrType InetAddressType,
pwIndexMappingPeerAddr InetAddress,
pwIndexMappingPwIndex PwIndexType
}
pwIndexMappingPwType OBJECT-TYPE
SYNTAX IANAPwTypeTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The PW type (indicates the service) of this PW."
::= { pwIndexMappingEntry 1 }
pwIndexMappingPwID OBJECT-TYPE
SYNTAX PwIDType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The PW ID of this PW. Zero if the PW is configured
manually."
::= { pwIndexMappingEntry 2 }
pwIndexMappingPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address type of the peer node."
::= { pwIndexMappingEntry 3 }
pwIndexMappingPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the peer node."
::= { pwIndexMappingEntry 4 }
pwIndexMappingPwIndex OBJECT-TYPE
SYNTAX PwIndexType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value that represents the PW in the pwTable."
::= { pwIndexMappingEntry 5 }
-- End of the PW ID mapping table
-- The peer mapping table
pwPeerMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF PwPeerMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides reverse mapping of the existing PW
based on PW type and PW ID ordering. This table is
typically useful for EMS ordered query of existing PWs."
::= { pwObjects 8 }
pwPeerMappingEntry OBJECT-TYPE
SYNTAX PwPeerMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for every
PW entry in pwTable.
Implementors need to be aware that if the value of the
pwPeerMappingPeerAddr (an OID) has more than 112
sub-identifiers, then OIDs of column instances in this
table will have more than 128 sub-identifiers and cannot
be accessed using SNMPv1, SNMPv2c, or SNMPv3."
INDEX { pwPeerMappingPeerAddrType, pwPeerMappingPeerAddr,
pwPeerMappingPwType, pwPeerMappingPwID }
::= { pwPeerMappingTable 1 }
PwPeerMappingEntry ::= SEQUENCE {
pwPeerMappingPeerAddrType InetAddressType,
pwPeerMappingPeerAddr InetAddress,
pwPeerMappingPwType IANAPwTypeTC,
pwPeerMappingPwID PwIDType,
pwPeerMappingPwIndex PwIndexType
}
pwPeerMappingPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address type of the peer node."
::= { pwPeerMappingEntry 1 }
pwPeerMappingPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the peer node."
::= { pwPeerMappingEntry 2 }
pwPeerMappingPwType OBJECT-TYPE
SYNTAX IANAPwTypeTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The PW type (indicates the emulated service) of this PW."
::= { pwPeerMappingEntry 3 }
pwPeerMappingPwID OBJECT-TYPE
SYNTAX PwIDType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The PW ID of this PW. Zero if the PW is configured
manually."
::= { pwPeerMappingEntry 4 }
pwPeerMappingPwIndex OBJECT-TYPE
SYNTAX PwIndexType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value that represents the PW in the pwTable."
::= { pwPeerMappingEntry 5 }
-- End of the peer mapping table
-- End of reverse mapping tables
pwUpDownNotifEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to true(1), then it enables
the emission of pwUp and pwDown
notifications; otherwise these notifications are not
emitted."
REFERENCE
"See also [RFC3413] for explanation that
notifications are under the ultimate control of the
MIB module in this document."
DEFVAL { false }
::= { pwObjects 9 }
pwDeletedNotifEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to true(1), then it enables the
emission of pwDeleted notification; otherwise this
notification is not emitted."
REFERENCE
"See also [RFC3413] for explanation that
notifications are under the ultimate control of the
MIB module in this document."
DEFVAL { false }
::= { pwObjects 10 }
pwNotifRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object defines the maximum number of PW notifications
that can be emitted from the device per second."
::= { pwObjects 11 }
-- Foundry Proprietary extension
fdryPwServiceType OBJECT-TYPE
SYNTAX FdryPwServiceType
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"A L2VPN service type, used only for notification.
"
::= { pwObjects 20 }
-- Notifications - PW
pwDown NOTIFICATION-TYPE
OBJECTS { pwOperStatus, --start of range
pwOperStatus, --end of range
fdryPwServiceType, -- properietary extension
snAgGblTrapMessage -- properietary extension
}
STATUS current
DESCRIPTION
"This notification is generated when the
pwOperStatus object for one or more contiguous
entries in pwTable are about to enter the
down(2) state from some other state. The included values
of pwOperStatus MUST all be set equal to this
down(2) state. The two instances of pwOperStatus
in this notification indicate the range of indexes
that are affected. Note that all the indexes of the
two ends of the range can be derived from the
instance identifiers of these two objects. For
cases where a contiguous range of cross-connects
have transitioned into the down(2) state at roughly
the same time, the device SHOULD issue a single
notification for each range of contiguous indexes in
an effort to minimize the emission of a large number
of notifications. If a notification has to be
issued for just a single cross-connect entry, then
the instance identifier (and values) of the two
pwOperStatus objects MUST be identical.
The varbind fdryPwServiceType, specifies the
service that originated this notification.
The varbind snAgGblTrapMessage displays the corresponding
SYSLOG content for this notification, which is more descriptive.
"
--#TYPE "Foundry Trap: MPLS Pseudo-Wire Down"
--#SUMMARY "%s."
--#ARGUMENTS { 3 }
--#SEVERITY WARNING
--#STATE OPERATIONAL
::= { pwNotifications 1 }
pwUp NOTIFICATION-TYPE
OBJECTS { pwOperStatus, --start of range
pwOperStatus, --end of range
fdryPwServiceType, -- properietary extension
snAgGblTrapMessage -- properietary extension
}
STATUS current
DESCRIPTION
"This notification is generated when the
pwOperStatus object for one or more contiguous
entries in pwTable are about to enter the up(1)
state from some other state. The included values of
pwOperStatus MUST both be set equal to this
new state (i.e: up(1)). The two instances of
pwOperStatus in this notification indicate the range
of indexes that are affected. Note that all the indexes
of the two ends of the range can be derived from the
instance identifiers of these two objects. For
cases where a contiguous range of cross-connects
have transitioned into the up(1) state at roughly
the same time, the device SHOULD issue a single
notification for each range of contiguous indexes in
an effort to minimize the emission of a large number
of notifications. If a notification has to be
issued for just a single cross-connect entry, then
the instance identifier (and values) of the two
pwOperStatus objects MUST be the identical.
The varbind fdryPwServiceType, specifies the
service that originated this notification.
The varbind snAgGblTrapMessage displays the corresponding
SYSLOG content for this notification, which is more descriptive.
"
--#TYPE "Foundry Trap: MPLS Pseudo-Wire Up"
--#SUMMARY "%s."
--#ARGUMENTS { 3 }
--#SEVERITY WARNING
--#STATE OPERATIONAL
::= { pwNotifications 2 }
pwDeleted NOTIFICATION-TYPE
OBJECTS { pwType,
pwID,
pwPeerAddrType,
pwPeerAddr,
fdryPwServiceType, -- properietary extension
pwName --proprietary extension
}
STATUS current
DESCRIPTION
"This notification is generated when the PW has been
deleted, i.e. when the pwRowStatus has been set to
destroy(6), the PW has been deleted by a non-MIB
application or due to auto-discovery process.
pwName varbind has been added as a proprietary extension
to provide a name, in addition to the pwID, which has the VC ID.
For VPLS PW, name is the VPLS instance name.
For VLL PW, it is the VLL instance name. Similarly, for VLL-Local PW,
it is the VLL-Local's instance name.
The varbind fdryPwServiceType, specifies the
service that originated this notification.
"
--#TYPE "Foundry Trap: MPLS Pseudo-Wire Deleted"
--#SUMMARY "PW %s (ID %d) with peer %s has been deleted."
--#ARGUMENTS { 5, 1, 3 }
--#SEVERITY WARNING
--#STATE OPERATIONAL
::= { pwNotifications 3 }
-- End of notifications.
-- Conformance information
pwGroups OBJECT IDENTIFIER ::= { pwConformance 1 }
pwCompliances OBJECT IDENTIFIER ::= { pwConformance 2 }
-- Compliance requirement for fully compliant implementations.
pwModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that provide full
support for PW MIB Module. Such devices can
then be monitored and configured using
this MIB module."
MODULE -- this module
MANDATORY-GROUPS { pwBasicGroup,
pwPerformanceGeneralGroup,
pwPeformanceTotalGroup
}
GROUP pwNotificationGroup
DESCRIPTION "This group is only mandatory for implementations
which can efficiently implement the notifications
contained in this group.
"
GROUP pwPwIdGroup
DESCRIPTION "This group is only mandatory for implementations
that support the PW ID FEC.
"
GROUP pwGeneralizedFecGroup
DESCRIPTION "This group is only mandatory for implementations
that support the generalized PW FEC.
"
GROUP pwFcsGroup
DESCRIPTION "This group is only mandatory for implementations
that support FCS retention."
GROUP pwFragGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW fragmentation.
"
GROUP pwPwStatusGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW status notification.
"
GROUP pwGetNextGroup
DESCRIPTION "This group is only mandatory for implementations
where the pwIndex may be any arbitrary value
and the EMS would require retrieval of the next
free index."
GROUP pwPriorityGroup
DESCRIPTION "This group is only mandatory for implementations
that support the controlling the PW setup and
holding priority."
GROUP pwAttachmentGroup
DESCRIPTION "This group is only mandatory for implementations
that support attachment of two PWs (PW stitching)."
GROUP pwPerformanceIntervalGeneralGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW performance gathering in 15
minute intervals."
GROUP pwPeformanceIntervalGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW performance gathering in 15
minute intervals."
GROUP pwHCPeformanceIntervalGroup
DESCRIPTION "This group is only mandatory for implementations
where at least one of the interval performance
counters wraps around too quickly based on the
criteria specified in RFC 2863 for high-capacity
counters."
GROUP pwMappingTablesGroup
DESCRIPTION "This group is only mandatory for implementations
that support reverse mapping of PW indexes to
the pwIndex and the peer mapping table."
GROUP pwSignalingGroup
DESCRIPTION "This group is only mandatory for implementations
that support the PW signaling."
GROUP pwNotificationControlGroup
DESCRIPTION "This group is only mandatory for implementations
that support the PW notifications."
OBJECT pwAdminStatus
SYNTAX INTEGER { up(1), down(2) }
DESCRIPTION "The support of the value testing(3) is not
required."
OBJECT pwOperStatus
SYNTAX INTEGER { up(1), down(2), notPresent(5),
lowerLayerDown(6) }
DESCRIPTION "The support of the values testing(3) and dormant(4)
is not required."
OBJECT pwRowStatus
SYNTAX INTEGER { active(1), notInService(2),
notReady(3) }
WRITE-SYNTAX INTEGER { active(1), notInService(2),
createAndGo(4), destroy(6)
}
DESCRIPTION "Support for createAndWait is not required. Support
of notReady is not required for implementations
that do not support signaling, or if it is
guaranteed that the conceptual row has all the
required information to create the PW when the
row has been created by the agent or written by
the operator."
OBJECT pwPeerAddrType
SYNTAX INTEGER { unknown(0), ipv4(1) }
MIN-ACCESS read-only
DESCRIPTION "Only unknown(0) and ipv4(1) is required.
Implementation that support only IPv4 MAY support
read-only access."
OBJECT pwPeerAddr
SYNTAX InetAddress (SIZE(0|4))
DESCRIPTION "An implementation is only required to support
0, 4 address sizes."
OBJECT pwStorageType
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwNotifRate
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
::= { pwCompliances 1 }
-- Compliance requirement for read-only compliant implementations.
pwModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that provide read-
only support for PW MIB Module. Such devices can
then be monitored but cannot be configured using this
MIB module."
MODULE -- this module
MANDATORY-GROUPS { pwBasicGroup,
pwPeformanceTotalGroup
}
GROUP pwNotificationGroup
DESCRIPTION "This group is only mandatory for implementations
which can efficiently implement the notifications
contained in this group."
GROUP pwPwIdGroup
DESCRIPTION "This group is only mandatory for implementations
that support the PW ID FEC.
"
GROUP pwGeneralizedFecGroup
DESCRIPTION "This group is only mandatory for implementations
that support the generalized PW FEC.
"
GROUP pwFcsGroup
DESCRIPTION "This group is only mandatory for implementations
that support FCS retention."
GROUP pwFragGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW fragmentation.
"
GROUP pwPwStatusGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW status notification.
"
GROUP pwGetNextGroup
DESCRIPTION "This group is only mandatory for implementations
where the pwIndex may be any arbitary value
and the EMS would require retrieval of the next
free index."
GROUP pwPriorityGroup
DESCRIPTION "This group is only mandatory for implementations
that support the controling the PW setup and
holding priority."
GROUP pwAttachmentGroup
DESCRIPTION "This group is only mandatory for implementations
that support attachment of two PWs (PW stitching)."
GROUP pwPerformanceIntervalGeneralGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW performance gathering in 15
minute intervals."
GROUP pwPeformanceIntervalGroup
DESCRIPTION "This group is only mandatory for implementations
that support PW performance gathering in 15
minute intervals."
GROUP pwHCPeformanceIntervalGroup
DESCRIPTION "This group is only mandatory for implementations
where at least one of the interval performance
counters wraps around too quickly based on the
criteria specified in RFC 2863 for high-capacity
counters."
GROUP pwMappingTablesGroup
DESCRIPTION "This group is only mandatory for implementations
that support reverse mapping of PW indexes to
the pwIndex and the peer mapping table."
GROUP pwSignalingGroup
DESCRIPTION "This group is only mandatory for implementations
that support the PW signaling."
GROUP pwNotificationControlGroup
DESCRIPTION "This group is only mandatory for implementations
that support the PW notifications."
OBJECT pwType
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwOwner
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwPsnType
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwSetUpPriority
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwHoldingPriority
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwPeerAddrType
SYNTAX INTEGER { unknown(0), ipv4(1) }
MIN-ACCESS read-only
DESCRIPTION "Write access is not required. Only unknown(0) and
ipv4(1) is required."
OBJECT pwPeerAddr
SYNTAX InetAddress (SIZE(0|4))
MIN-ACCESS read-only
DESCRIPTION "Write access is not required. An implementation
is only required to support 0, 4 address sizes."
OBJECT pwAttachedPwIndex
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwIfIndex
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwID
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwLocalGroupID
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwGroupAttachmentID
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwLocalAttachmentID
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwPeerAttachmentID
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwCwPreference
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwLocalIfMtu
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwLocalIfString
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwLocalCapabAdvert
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwFragmentCfgSize
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwFcsRetentionCfg
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwOutboundLabel
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwInboundLabel
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwName
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwDescr
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwAdminStatus
SYNTAX INTEGER { up(1), down(2) }
MIN-ACCESS read-only
DESCRIPTION "Write access is not required. The support of value
testing(3) is not required."
OBJECT pwOperStatus
SYNTAX INTEGER { up(1), down(2), notPresent(5),
lowerLayerDown(6) }
DESCRIPTION "The support of the values testing(3) and dormant(4)
is not required."
OBJECT pwRowStatus
SYNTAX INTEGER { active(1) }
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwStorageType
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwUpDownNotifEnable
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwDeletedNotifEnable
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT pwNotifRate
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
::= { pwCompliances 2 }
-- Units of conformance.
pwBasicGroup OBJECT-GROUP
OBJECTS {
pwType,
pwOwner,
pwPsnType,
pwIfIndex,
pwCwPreference,
pwLocalIfMtu,
pwOutboundLabel,
pwInboundLabel,
pwName,
pwDescr,
pwCreateTime,
pwUpTime,
pwLastChange,
pwAdminStatus,
pwOperStatus,
pwLocalStatus,
pwRowStatus,
pwStorageType,
pwOamEnable
}
STATUS current
DESCRIPTION
"Collection of objects that are required in all
implementations that support the PW MIB module."
::= { pwGroups 1 }
pwPwIdGroup OBJECT-GROUP
OBJECTS {
pwID
}
STATUS current
DESCRIPTION
"Collection of objects required for PW ID configuration
and signaling."
::= { pwGroups 2 }
pwGeneralizedFecGroup OBJECT-GROUP
OBJECTS {
pwGroupAttachmentID,
pwLocalAttachmentID,
pwPeerAttachmentID
}
STATUS current
DESCRIPTION
"Collection of objects required for generalized FEC
configuration and signaling."
::= { pwGroups 3 }
pwFcsGroup OBJECT-GROUP
OBJECTS {
pwFcsRetentionCfg,
pwFcsRetentionStatus
}
STATUS current
DESCRIPTION
"Collection of objects required for FCS retention
configuration and signaling."
::= { pwGroups 4 }
pwFragGroup OBJECT-GROUP
OBJECTS {
pwFragmentCfgSize,
pwRmtFragCapability
}
STATUS current
DESCRIPTION
"Collection of objects required for fragmentation
configuration and signaling."
::= { pwGroups 5 }
pwPwStatusGroup OBJECT-GROUP
OBJECTS {
pwRemoteCapabilities,
pwRemoteStatusCapable,
pwRemoteStatus
}
STATUS current
DESCRIPTION
"Collection of objects required for PW status configuration
and signaling."
::= { pwGroups 6 }
pwGetNextGroup OBJECT-GROUP
OBJECTS {
pwIndexNext
}
STATUS current
DESCRIPTION
"Collection of objects for getting the next available
index."
::= { pwGroups 7 }
pwPriorityGroup OBJECT-GROUP
OBJECTS {
pwSetUpPriority,
pwHoldingPriority
}
STATUS current
DESCRIPTION
"Collection of objects for controlling the PW setup and
holding priority."
::= { pwGroups 8 }
pwAttachmentGroup OBJECT-GROUP
OBJECTS {
pwAttachedPwIndex
}
STATUS current
DESCRIPTION
"Collection of objects for PW configuration as ifIndex"
::= { pwGroups 9 }
pwPerformanceGeneralGroup OBJECT-GROUP
OBJECTS {
pwPerfTotalErrorPackets
}
STATUS current
DESCRIPTION
"Collection of general objects needed for managing the
total running performance parameters."
::= { pwGroups 10 }
pwPeformanceTotalGroup OBJECT-GROUP
OBJECTS {
pwPerfTotalInPackets,
pwPerfTotalInBytes,
pwPerfTotalOutPackets,
pwPerfTotalOutBytes
}
STATUS current
DESCRIPTION
"Collection of 32 bits objects needed for PW running total
performance collection."
::= { pwGroups 11 }
pwPerformanceIntervalGeneralGroup OBJECT-GROUP
OBJECTS {
pwTimeElapsed,
pwValidIntervals,
pwPerfIntervalValidData,
pwPerfIntervalTimeElapsed
}
STATUS current
DESCRIPTION
"Collection of general objects needed for managing the
interval performance parameters."
::= { pwGroups 12 }
pwPeformanceIntervalGroup OBJECT-GROUP
OBJECTS {
pwPerfCurrentInPackets,
pwPerfCurrentInBytes,
pwPerfCurrentOutPackets,
pwPerfCurrentOutBytes,
pwPerfIntervalInPackets,
pwPerfIntervalInBytes,
pwPerfIntervalOutPackets,
pwPerfIntervalOutBytes
}
STATUS current
DESCRIPTION
"Collection of 32 bits objects needed for PW performance
collection in 15 minutes intervals."
::= { pwGroups 13 }
pwHCPeformanceIntervalGroup OBJECT-GROUP
OBJECTS {
pwPerfCurrentInHCPackets,
pwPerfCurrentInHCBytes,
pwPerfCurrentOutHCPackets,
pwPerfCurrentOutHCBytes,
pwPerfIntervalInHCPackets,
pwPerfIntervalInHCBytes,
pwPerfIntervalOutHCPackets,
pwPerfIntervalOutHCBytes
}
STATUS current
DESCRIPTION
"Collection of HC objects needed for PW performance
collection in 15 minutes intervals."
::= { pwGroups 14 }
pwMappingTablesGroup OBJECT-GROUP
OBJECTS {
pwIndexMappingPwIndex,
pwPeerMappingPwIndex
}
STATUS current
DESCRIPTION
"Collection of objects contained in the reverse
mapping tables."
::= { pwGroups 15 }
pwNotificationControlGroup OBJECT-GROUP
OBJECTS {
pwUpDownNotifEnable,
pwDeletedNotifEnable,
pwNotifRate
}
STATUS current
DESCRIPTION
"Collection of objects for controlling the PW
notifications."
::= { pwGroups 16 }
pwNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
pwUp,
pwDown,
pwDeleted
}
STATUS current
DESCRIPTION
"Collection PW notifications objects."
::= { pwGroups 17 }
pwSignalingGroup OBJECT-GROUP
OBJECTS {
pwPeerAddrType,
pwPeerAddr,
pwLocalGroupID,
pwLocalIfString,
pwLocalCapabAdvert,
pwRemoteGroupID,
pwCwStatus,
pwRemoteIfMtu,
pwRemoteIfString
}
STATUS current
DESCRIPTION
"Collection of objects for use in implementations that
support the PW signaling."
::= { pwGroups 18 }
END
Reference in New Issue View Git Blame Copy Permalink