-- ***************************************************************** -- CISCO-LAG-MIB.my: Cisco LAG MIB -- -- October 2001, Liwei Lue -- -- Copyright (c) 2001-2003, 2004, 2006, 2008 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-LAG-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION FROM SNMPv2-TC ciscoMgmt FROM CISCO-SMI dot3adAggPortEntry, dot3adAggPortListEntry FROM IEEE8023-LAG-MIB ifIndex FROM IF-MIB; ciscoLagMIB MODULE-IDENTITY LAST-UPDATED "200801080000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-etherchan@cisco.com cs-lan-switch-snmp@cisco.com" DESCRIPTION "Cisco Link Aggregation module for managing IEEE Std 802.3ad. This MIB provides Link Aggregation information that are either excluded by IEEE Std 802.3ad (IEEE8023-LAG-MIB) or specific to Cisco products." REVISION "200801080000Z" DESCRIPTION "Modified the description of clagAggPortListPorts." REVISION "200606210000Z" DESCRIPTION "Added clagAggMaxAggregatorsGroup and modified the description of clagAggPortListPorts." REVISION "200406110000Z" DESCRIPTION "Added clagAggPortListTable." REVISION "200212130000Z" DESCRIPTION "Added a new value vlanIpPort(4) in TEXTUAL-CONVENTION ClagDistributionProtocol. Added a new object clagAggDistributionMplsProtocol." REVISION "200201020000Z" DESCRIPTION "Modified Description of clagAggDistributionProtocol." REVISION "200110230000Z" DESCRIPTION "Initial version of this MIB module. Support Distribution configuration for LACP, Aggregation protocol control, and Administrative status for LACP." ::= { ciscoMgmt 225 } clagMIBObjects OBJECT IDENTIFIER ::= { ciscoLagMIB 1 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- ClagDistributionProtocol ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An enumerated type for all the supported load balancing algorithms used on the LACP interface to distribute outgoing data frames among its component interaces, such as IP address. ip(1) IP address mac(2) MAC address port(3) port number vlanIpPort(4) vlan number, IP address and port number" SYNTAX INTEGER { ip(1), mac(2), port(3), vlanIpPort(4) } ClagDistributionAddressMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An enumerated type for all the supported load balancing address modes to distribute traffic across multiple links. The address mode can be source, destination, or both used on this LACP interface to distribute outgoing data frames among its component interfaces. source(1) Source address. destination(2) Destination address. both(3) both, Source and Destination." SYNTAX INTEGER { source(1), destination(2), both(3) } ClagDistributionMplsProtocol ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An enumerated type for all the supported load balancing algorithms used on the LACP interface to distribute outgoing MPLS (Multi-Protocol Label Switching) data frames among its component interfaces, such as MPLS label. label(1) MPLS label labelIp(2) MPLS label or IP address" SYNTAX INTEGER { label(1), labelIp(2) } ClagAggregationProtocol ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An enumerated type for all the supported aggregation protocols. lacp(1) Link Aggregation Control Protocol(LACP), IEEE 802.3ad pagp(2) Port Aggregation Protocol" SYNTAX INTEGER { lacp(1), pagp(2) } ClagPortAdminStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An enumerated type for all the LACP administrative states on a particular aggregation port. off(1) No LACP involved on the aggregation port. on(2) The aggregation port always join link aggregation whithout any LACP protocol involved. active(3) Active LACP indicates the port's preference to participate in the protocol regardless of Partner's control value. passive(4) Passive indicates the port's preference for not transmitting LACP PDU unless its Partner's control value is Active LACP." SYNTAX INTEGER { off(1), on(2), active(3), passive(4) } -- ------------------------------------------------------------- -- -- ------------------------------------------------------------- -- groups in the LAG MIB -- ------------------------------------------------------------- clagGlobalConfigObjects OBJECT IDENTIFIER ::= { clagMIBObjects 1 } clagAgg OBJECT IDENTIFIER ::= { clagMIBObjects 2 } clagAggPort OBJECT IDENTIFIER ::= { clagMIBObjects 3 } clagAggPortList OBJECT IDENTIFIER ::= { clagMIBObjects 4 } -- ------------------------------------------------------------- -- -- ------------------------------------------------------------- -- The Aggregation Global Configuration -- ------------------------------------------------------------- clagAggDistributionProtocol OBJECT-TYPE SYNTAX ClagDistributionProtocol MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the load balancing algorithms used on this LACP interface to distribute outgoing data frames among its component interfaces." ::= { clagGlobalConfigObjects 1 } clagAggDistributionAddressMode OBJECT-TYPE SYNTAX ClagDistributionAddressMode MAX-ACCESS read-write STATUS current DESCRIPTION "The load balancing address mode for the device." ::= { clagGlobalConfigObjects 2 } clagAggDistributionMplsProtocol OBJECT-TYPE SYNTAX ClagDistributionMplsProtocol MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the load balancing algorithms used on this LACP interface to distribute outgoing MPLS data frames among its component interfaces. This object is only instantiated on platforms which support aggregation load balancing for MPLS packets." ::= { clagGlobalConfigObjects 3 } clagAggMaxAggregators OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of aggregators supported by the device." ::= { clagGlobalConfigObjects 4 } -- ------------------------------------------------------------- -- The Aggregation Protocol Table -- ------------------------------------------------------------- clagAggProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF ClagAggProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains protocol information about every interface which supports link aggregation." ::= { clagAgg 1 } clagAggProtocolEntry OBJECT-TYPE SYNTAX ClagAggProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing aggregation protocol type for a particular interface. An entry is created in this table when its associated ifEntry is created and that interface supports link aggregation. The entry of this table is deleted when the associated ifEntry is removed." INDEX { ifIndex } ::= { clagAggProtocolTable 1 } ClagAggProtocolEntry ::= SEQUENCE { clagAggProtocolType ClagAggregationProtocol } clagAggProtocolType OBJECT-TYPE SYNTAX ClagAggregationProtocol MAX-ACCESS read-write STATUS current DESCRIPTION "The aggregation protocol type for the interface. On some platforms, aggregation protocol may be assigned per group. The group can be a collection of the ports which belong to a module or system. If the aggregation protocol is assigned to any of the ports in such group then the aggregation protocol will apply to all ports in the same group. On some platforms, aggregation protocol type can be assigned per aggregator. If multiple ports belong to a aggregator, the aggregation protocol assigned to any of the ports in such aggregator will apply to all ports in the same." ::= { clagAggProtocolEntry 1 } -- ------------------------------------------------------------- -- The Aggregation Port Configuration Table -- ------------------------------------------------------------- clagAggPortTable OBJECT-TYPE SYNTAX SEQUENCE OF ClagAggPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about every aggregation port that is associated with this system. This table contains additional objects for the dot3adAggPortTable." REFERENCE "IEEE 802.3 Subclause 30.7.2" ::= { clagAggPort 1 } clagAggPortEntry OBJECT-TYPE SYNTAX ClagAggPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing additional management information applicable to a particular aggregation port." AUGMENTS { dot3adAggPortEntry } ::= { clagAggPortTable 1 } ClagAggPortEntry ::= SEQUENCE { clagAggPortAdminStatus ClagPortAdminStatus } clagAggPortAdminStatus OBJECT-TYPE SYNTAX ClagPortAdminStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative status of the LACP protocol on this aggregation port." ::= { clagAggPortEntry 1 } -- ------------------------------------------------------------- -- The Port List Table -- ------------------------------------------------------------- clagAggPortListTable OBJECT-TYPE SYNTAX SEQUENCE OF ClagAggPortListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table augments the dot3adAggPortListTable and provides the complete list of ports associated with each Aggregator." REFERENCE "IEEE 802.3 Subclause 30.7.1.1.30" ::= { clagAggPortList 1 } clagAggPortListEntry OBJECT-TYPE SYNTAX ClagAggPortListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the ports associated with a given Aggregator." AUGMENTS { dot3adAggPortListEntry } ::= { clagAggPortListTable 1 } ClagAggPortListEntry ::= SEQUENCE { clagAggPortListPorts OCTET STRING } clagAggPortListPorts OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains a list of ports currently associated with this Aggregator in the format of '[number_of_ports][cieIfDot1dBaseMappingPort1][...] [cieIfDot1dBaseMappingPortn]' where [number_of_ports] is of size 2 octet and indicates the number of ports contains in this object. It also indicates the number of cieIfDot1dBaseMappingPort field following this field. [cieIfDot1dBaseMappingPort'n'] is the value of cieIfDot1dBaseMappingPort of the 'n' port associated with this Aggregation and has size of 2 octets where n is up to [number_of_ports]." REFERENCE "IEEE 802.3 Subclause 30.7.1.1.30" ::= { clagAggPortListEntry 1 } -- ------------------------------------------------------------- -- -- ------------------------------------------------------------- -- Notifications -- ------------------------------------------------------------- clagMIBNotifications OBJECT IDENTIFIER ::= { ciscoLagMIB 2 } -- no notifications defined -- -- ------------------------------------------------------------- -- Conformance -- ------------------------------------------------------------- clagMIBConformance OBJECT IDENTIFIER ::= { ciscoLagMIB 3 } clagMIBCompliances OBJECT IDENTIFIER ::= { clagMIBConformance 1 } clagMIBGroups OBJECT IDENTIFIER ::= { clagMIBConformance 2 } -- ------------------------------------------------------------- -- -- ------------------------------------------------------------- -- Compliance -- ------------------------------------------------------------- clagMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Link Aggregation MIB" MODULE -- this module MANDATORY-GROUPS { clagAggProtocolGroup, clagAggPortGroup } GROUP clagAggDistributionGroup DESCRIPTION "This group is mandatory for the devices which supported aggregation load balancing." OBJECT clagAggProtocolType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clagAggPortAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { clagMIBCompliances 1 } clagMIBCompliance2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Link Aggregation MIB" MODULE -- this module MANDATORY-GROUPS { clagAggProtocolGroup, clagAggPortGroup } GROUP clagAggDistributionGroup DESCRIPTION "This group is mandatory for the devices which supported aggregation load balancing." GROUP clagAggDistributionMplsGroup DESCRIPTION "This group is mandatory for the devices which supported aggregation load balancing for MPLS packets." OBJECT clagAggProtocolType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clagAggPortAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { clagMIBCompliances 2 } clagMIBCompliance3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Link Aggregation MIB" MODULE -- this module MANDATORY-GROUPS { clagAggProtocolGroup, clagAggPortGroup } GROUP clagAggDistributionGroup DESCRIPTION "This group is mandatory for the devices which supported aggregation load balancing." GROUP clagAggDistributionMplsGroup DESCRIPTION "This group is mandatory for the devices which supported aggregation load balancing for MPLS packets." GROUP clagAggPortListGroup DESCRIPTION "This group is mandatory for the devices which supports dot1dBasePort value greater than 2048." OBJECT clagAggProtocolType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clagAggPortAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { clagMIBCompliances 3 } clagMIBCompliance4 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Cisco Link Aggregation MIB" MODULE -- this module MANDATORY-GROUPS { clagAggProtocolGroup, clagAggPortGroup } GROUP clagAggDistributionGroup DESCRIPTION "This group is mandatory for the devices which supported aggregation load balancing." GROUP clagAggDistributionMplsGroup DESCRIPTION "This group is mandatory for the devices which supported aggregation load balancing for MPLS packets." GROUP clagAggPortListGroup DESCRIPTION "This group is mandatory for the devices which supports dot1dBasePort value greater than 2048." GROUP clagAggMaxAggregatorsGroup DESCRIPTION "This group is mandatory for the devices which provides the information about the maximum number of aggregators supported by the device." OBJECT clagAggProtocolType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clagAggPortAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { clagMIBCompliances 4 } -- ------------------------------------------------------------- -- Units of Conformance -- ------------------------------------------------------------- clagAggProtocolGroup OBJECT-GROUP OBJECTS { clagAggProtocolType } STATUS current DESCRIPTION "The object that provide aggregation protocol type of an interface. These are additional to the IEEE Std 802.3ad MIB." ::= { clagMIBGroups 1 } clagAggPortGroup OBJECT-GROUP OBJECTS { clagAggPortAdminStatus } STATUS current DESCRIPTION "A collection of objects that provide admin status about an aggregation port. These are additional to the IEEE Std 802.3ad MIB." ::= { clagMIBGroups 2 } clagAggDistributionGroup OBJECT-GROUP OBJECTS { clagAggDistributionProtocol, clagAggDistributionAddressMode } STATUS current DESCRIPTION "A collection of objects that provide the load balancing information for an aggregator. These are additional to the IEEE Std 802.3ad MIB." ::= { clagMIBGroups 3 } clagAggDistributionMplsGroup OBJECT-GROUP OBJECTS { clagAggDistributionMplsProtocol } STATUS current DESCRIPTION "A collection of objects that provide the load balancing information for an aggregator for MPLS packets. These are additional to the IEEE Std 802.3ad MIB." ::= { clagMIBGroups 4 } clagAggPortListGroup OBJECT-GROUP OBJECTS { clagAggPortListPorts } STATUS current DESCRIPTION "A collection of object that provides information about ports in an aggregation." ::= { clagMIBGroups 5 } clagAggMaxAggregatorsGroup OBJECT-GROUP OBJECTS { clagAggMaxAggregators } STATUS current DESCRIPTION "A collection of object that provides information about the maximum number of aggregators supported by the device." ::= { clagMIBGroups 6 } END