mirror of
https://github.com/Xinyuan-LilyGO/TTGO-T-Display.git
synced 2024-09-21 09:57:27 +00:00
456 lines
17 KiB
C
456 lines
17 KiB
C
////////////////////////////////////////////////////
|
|
// TFT_eSPI driver functions for ESP32 processors //
|
|
////////////////////////////////////////////////////
|
|
|
|
#ifndef _TFT_eSPI_ESP32H_
|
|
#define _TFT_eSPI_ESP32H_
|
|
|
|
// Processor ID reported by getSetup()
|
|
#define PROCESSOR_ID 0x32
|
|
|
|
// Include processor specific header
|
|
#include "soc/spi_reg.h"
|
|
#include "driver/spi_master.h"
|
|
|
|
// Processor specific code used by SPI bus transaction startWrite and endWrite functions
|
|
#define SET_BUS_WRITE_MODE // Not used
|
|
#define SET_BUS_READ_MODE // Not used
|
|
|
|
// SUPPORT_TRANSACTIONS is mandatory for ESP32 so the hal mutex is toggled
|
|
#if !defined (SUPPORT_TRANSACTIONS)
|
|
#define SUPPORT_TRANSACTIONS
|
|
#endif
|
|
|
|
// ESP32 specific SPI port selection
|
|
#ifdef USE_HSPI_PORT
|
|
#define SPI_PORT HSPI
|
|
#else
|
|
#define SPI_PORT VSPI
|
|
#endif
|
|
|
|
#ifdef RPI_DISPLAY_TYPE
|
|
#define CMD_BITS (16-1)
|
|
#else
|
|
#define CMD_BITS (8-1)
|
|
#endif
|
|
|
|
// Initialise processor specific SPI functions, used by init()
|
|
#define INIT_TFT_DATA_BUS // Not used
|
|
|
|
// Define a generic flag for 8 bit parallel
|
|
#if defined (ESP32_PARALLEL) // Specific to ESP32 for backwards compatibility
|
|
#if !defined (TFT_PARALLEL_8_BIT)
|
|
#define TFT_PARALLEL_8_BIT // Generic parallel flag
|
|
#endif
|
|
#endif
|
|
|
|
// Ensure ESP32 specific flag is defined for 8 bit parallel
|
|
#if defined (TFT_PARALLEL_8_BIT)
|
|
#if !defined (ESP32_PARALLEL)
|
|
#define ESP32_PARALLEL
|
|
#endif
|
|
#endif
|
|
|
|
// Code to check if DMA is busy, used by SPI bus transaction transaction and endWrite functions
|
|
#if !defined(TFT_PARALLEL_8_BIT) && !defined(ILI9488_DRIVER) && !defined (RPI_DISPLAY_TYPE)
|
|
#define ESP32_DMA
|
|
// Code to check if DMA is busy, used by SPI DMA + transaction + endWrite functions
|
|
#define DMA_BUSY_CHECK dmaWait()
|
|
#else
|
|
#define DMA_BUSY_CHECK
|
|
#endif
|
|
|
|
// If smooth font is used then it is likely SPIFFS will be needed
|
|
#ifdef SMOOTH_FONT
|
|
// Call up the SPIFFS (SPI FLASH Filing System) for the anti-aliased fonts
|
|
#define FS_NO_GLOBALS
|
|
#include <FS.h>
|
|
#include "SPIFFS.h" // ESP32 only
|
|
#define FONT_FS_AVAILABLE
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Define the DC (TFT Data/Command or Register Select (RS))pin drive code
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#ifndef TFT_DC
|
|
#define DC_C // No macro allocated so it generates no code
|
|
#define DC_D // No macro allocated so it generates no code
|
|
#else
|
|
#if defined (TFT_PARALLEL_8_BIT)
|
|
// TFT_DC, by design, must be in range 0-31 for single register parallel write
|
|
#if (TFT_DC >= 0) && (TFT_DC < 32)
|
|
#define DC_C GPIO.out_w1tc = (1 << TFT_DC)
|
|
#define DC_D GPIO.out_w1ts = (1 << TFT_DC)
|
|
#else
|
|
#define DC_C
|
|
#define DC_D
|
|
#endif
|
|
#else
|
|
#if (TFT_DC >= 32)
|
|
#ifdef RPI_DISPLAY_TYPE // RPi displays need a slower DC change
|
|
#define DC_C GPIO.out1_w1ts.val = (1 << (TFT_DC - 32)); \
|
|
GPIO.out1_w1tc.val = (1 << (TFT_DC - 32))
|
|
#define DC_D GPIO.out1_w1tc.val = (1 << (TFT_DC - 32)); \
|
|
GPIO.out1_w1ts.val = (1 << (TFT_DC - 32))
|
|
#else
|
|
#define DC_C GPIO.out1_w1tc.val = (1 << (TFT_DC - 32))//;GPIO.out1_w1tc.val = (1 << (TFT_DC - 32))
|
|
#define DC_D GPIO.out1_w1ts.val = (1 << (TFT_DC - 32))//;GPIO.out1_w1ts.val = (1 << (TFT_DC - 32))
|
|
#endif
|
|
#elif (TFT_DC >= 0)
|
|
#if defined (RPI_DISPLAY_TYPE)
|
|
#if defined (ILI9486_DRIVER)
|
|
// RPi ILI9486 display needs a slower DC change
|
|
#define DC_C GPIO.out_w1tc = (1 << TFT_DC); \
|
|
GPIO.out_w1tc = (1 << TFT_DC)
|
|
#define DC_D GPIO.out_w1tc = (1 << TFT_DC); \
|
|
GPIO.out_w1ts = (1 << TFT_DC)
|
|
#else
|
|
// Other RPi displays need a slower C->D change
|
|
#define DC_C GPIO.out_w1tc = (1 << TFT_DC)
|
|
#define DC_D GPIO.out_w1tc = (1 << TFT_DC); \
|
|
GPIO.out_w1ts = (1 << TFT_DC)
|
|
#endif
|
|
#else
|
|
#define DC_C GPIO.out_w1tc = (1 << TFT_DC)//;GPIO.out_w1tc = (1 << TFT_DC)
|
|
#define DC_D GPIO.out_w1ts = (1 << TFT_DC)//;GPIO.out_w1ts = (1 << TFT_DC)
|
|
#endif
|
|
#else
|
|
#define DC_C
|
|
#define DC_D
|
|
#endif
|
|
#endif
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Define the CS (TFT chip select) pin drive code
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#ifndef TFT_CS
|
|
#define TFT_CS -1 // Keep DMA code happy
|
|
#define CS_L // No macro allocated so it generates no code
|
|
#define CS_H // No macro allocated so it generates no code
|
|
#else
|
|
#if defined (TFT_PARALLEL_8_BIT)
|
|
#if TFT_CS >= 32
|
|
#define CS_L GPIO.out1_w1tc.val = (1 << (TFT_CS - 32))
|
|
#define CS_H GPIO.out1_w1ts.val = (1 << (TFT_CS - 32))
|
|
#elif TFT_CS >= 0
|
|
#define CS_L GPIO.out_w1tc = (1 << TFT_CS)
|
|
#define CS_H GPIO.out_w1ts = (1 << TFT_CS)
|
|
#else
|
|
#define CS_L
|
|
#define CS_H
|
|
#endif
|
|
#else
|
|
#if (TFT_CS >= 32)
|
|
#ifdef RPI_DISPLAY_TYPE // RPi display needs a slower CS change
|
|
#define CS_L GPIO.out1_w1ts.val = (1 << (TFT_CS - 32)); \
|
|
GPIO.out1_w1tc.val = (1 << (TFT_CS - 32))
|
|
#define CS_H GPIO.out1_w1tc.val = (1 << (TFT_CS - 32)); \
|
|
GPIO.out1_w1ts.val = (1 << (TFT_CS - 32))
|
|
#else
|
|
#define CS_L GPIO.out1_w1tc.val = (1 << (TFT_CS - 32)); GPIO.out1_w1tc.val = (1 << (TFT_CS - 32))
|
|
#define CS_H GPIO.out1_w1ts.val = (1 << (TFT_CS - 32))//;GPIO.out1_w1ts.val = (1 << (TFT_CS - 32))
|
|
#endif
|
|
#elif (TFT_CS >= 0)
|
|
#ifdef RPI_DISPLAY_TYPE // RPi display needs a slower CS change
|
|
#define CS_L GPIO.out_w1ts = (1 << TFT_CS); GPIO.out_w1tc = (1 << TFT_CS)
|
|
#define CS_H GPIO.out_w1tc = (1 << TFT_CS); GPIO.out_w1ts = (1 << TFT_CS)
|
|
#else
|
|
#define CS_L GPIO.out_w1tc = (1 << TFT_CS); GPIO.out_w1tc = (1 << TFT_CS)
|
|
#define CS_H GPIO.out_w1ts = (1 << TFT_CS)//;GPIO.out_w1ts = (1 << TFT_CS)
|
|
#endif
|
|
#else
|
|
#define CS_L
|
|
#define CS_H
|
|
#endif
|
|
#endif
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Define the WR (TFT Write) pin drive code
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#if defined (TFT_WR)
|
|
#if (TFT_WR >= 0)
|
|
// TFT_WR, by design, must be in range 0-31 for single register parallel write
|
|
#define WR_L GPIO.out_w1tc = (1 << TFT_WR)
|
|
#define WR_H GPIO.out_w1ts = (1 << TFT_WR)
|
|
#else
|
|
#define WR_L
|
|
#define WR_H
|
|
#endif
|
|
#else
|
|
#define WR_L
|
|
#define WR_H
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Define the touch screen chip select pin drive code
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#ifndef TOUCH_CS
|
|
#define T_CS_L // No macro allocated so it generates no code
|
|
#define T_CS_H // No macro allocated so it generates no code
|
|
#else // XPT2046 is slow, so use slower digitalWrite here
|
|
#define T_CS_L digitalWrite(TOUCH_CS, LOW)
|
|
#define T_CS_H digitalWrite(TOUCH_CS, HIGH)
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Make sure SPI default pins are assigned if not specified by user or set to -1
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#if !defined (TFT_PARALLEL_8_BIT)
|
|
|
|
#ifdef USE_HSPI_PORT
|
|
|
|
#ifndef TFT_MISO
|
|
#define TFT_MISO 12
|
|
#endif
|
|
#if (TFT_MISO == -1)
|
|
#undef TFT_MISO
|
|
#define TFT_MISO 12
|
|
#endif
|
|
|
|
#ifndef TFT_MOSI
|
|
#define TFT_MOSI 13
|
|
#endif
|
|
#if (TFT_MOSI == -1)
|
|
#undef TFT_MOSI
|
|
#define TFT_MOSI 13
|
|
#endif
|
|
|
|
#ifndef TFT_SCLK
|
|
#define TFT_SCLK 14
|
|
#endif
|
|
#if (TFT_SCLK == -1)
|
|
#undef TFT_SCLK
|
|
#define TFT_SCLK 14
|
|
#endif
|
|
|
|
#else // VSPI port
|
|
|
|
#ifndef TFT_MISO
|
|
#define TFT_MISO 19
|
|
#endif
|
|
#if (TFT_MISO == -1)
|
|
#undef TFT_MISO
|
|
#define TFT_MISO 19
|
|
#endif
|
|
|
|
#ifndef TFT_MOSI
|
|
#define TFT_MOSI 23
|
|
#endif
|
|
#if (TFT_MOSI == -1)
|
|
#undef TFT_MOSI
|
|
#define TFT_MOSI 23
|
|
#endif
|
|
|
|
#ifndef TFT_SCLK
|
|
#define TFT_SCLK 18
|
|
#endif
|
|
#if (TFT_SCLK == -1)
|
|
#undef TFT_SCLK
|
|
#define TFT_SCLK 18
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Define the parallel bus interface chip pin drive code
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#if defined (TFT_PARALLEL_8_BIT)
|
|
|
|
// Create a bit set lookup table for data bus - wastes 1kbyte of RAM but speeds things up dramatically
|
|
// can then use e.g. GPIO.out_w1ts = set_mask(0xFF); to set data bus to 0xFF
|
|
#define CONSTRUCTOR_INIT_TFT_DATA_BUS \
|
|
for (int32_t c = 0; c<256; c++) \
|
|
{ \
|
|
xset_mask[c] = 0; \
|
|
if ( c & 0x01 ) xset_mask[c] |= (1 << TFT_D0); \
|
|
if ( c & 0x02 ) xset_mask[c] |= (1 << TFT_D1); \
|
|
if ( c & 0x04 ) xset_mask[c] |= (1 << TFT_D2); \
|
|
if ( c & 0x08 ) xset_mask[c] |= (1 << TFT_D3); \
|
|
if ( c & 0x10 ) xset_mask[c] |= (1 << TFT_D4); \
|
|
if ( c & 0x20 ) xset_mask[c] |= (1 << TFT_D5); \
|
|
if ( c & 0x40 ) xset_mask[c] |= (1 << TFT_D6); \
|
|
if ( c & 0x80 ) xset_mask[c] |= (1 << TFT_D7); \
|
|
} \
|
|
|
|
// Mask for the 8 data bits to set pin directions
|
|
#define dir_mask ((1 << TFT_D0) | (1 << TFT_D1) | (1 << TFT_D2) | (1 << TFT_D3) | (1 << TFT_D4) | (1 << TFT_D5) | (1 << TFT_D6) | (1 << TFT_D7))
|
|
|
|
// Data bits and the write line are cleared to 0 in one step
|
|
#define clr_mask (dir_mask | (1 << TFT_WR))
|
|
|
|
// A lookup table is used to set the different bit patterns, this uses 1kByte of RAM
|
|
#define set_mask(C) xset_mask[C] // 63fps Sprite rendering test 33% faster, graphicstest only 1.8% faster than shifting in real time
|
|
|
|
// Real-time shifting alternative to above to save 1KByte RAM, 47 fps Sprite rendering test
|
|
/*#define set_mask(C) (((C)&0x80)>>7)<<TFT_D7 | (((C)&0x40)>>6)<<TFT_D6 | (((C)&0x20)>>5)<<TFT_D5 | (((C)&0x10)>>4)<<TFT_D4 | \
|
|
(((C)&0x08)>>3)<<TFT_D3 | (((C)&0x04)>>2)<<TFT_D2 | (((C)&0x02)>>1)<<TFT_D1 | (((C)&0x01)>>0)<<TFT_D0
|
|
//*/
|
|
|
|
// Write 8 bits to TFT
|
|
#define tft_Write_8(C) GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t)(C)); WR_H
|
|
|
|
#if defined (SSD1963_DRIVER)
|
|
|
|
// Write 18 bit color to TFT
|
|
#define tft_Write_16(C) GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) (((C) & 0xF800)>> 8)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) (((C) & 0x07E0)>> 3)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) (((C) & 0x001F)<< 3)); WR_H
|
|
|
|
// 18 bit color write with swapped bytes
|
|
#define tft_Write_16S(C) uint16_t Cswap = ((C) >>8 | (C) << 8); tft_Write_16(Cswap)
|
|
|
|
#else
|
|
|
|
// Write 16 bits to TFT
|
|
#define tft_Write_16(C) GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 8)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 0)); WR_H
|
|
|
|
// 16 bit write with swapped bytes
|
|
#define tft_Write_16S(C) GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 0)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 8)); WR_H
|
|
#endif
|
|
|
|
// Write 32 bits to TFT
|
|
#define tft_Write_32(C) GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 24)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 16)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 8)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 0)); WR_H
|
|
|
|
// Write two concatenated 16 bit values to TFT
|
|
#define tft_Write_32C(C,D) GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 8)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 0)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((D) >> 8)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((D) >> 0)); WR_H
|
|
|
|
// Write 16 bit value twice to TFT - used by drawPixel()
|
|
#define tft_Write_32D(C) GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 8)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 0)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 8)); WR_H; \
|
|
GPIO.out_w1tc = clr_mask; GPIO.out_w1ts = set_mask((uint8_t) ((C) >> 0)); WR_H
|
|
|
|
// Read pin
|
|
#ifdef TFT_RD
|
|
#if (TFT_RD >= 32)
|
|
#define RD_L GPIO.out1_w1tc.val = = (1 << (TFT_RD - 32))
|
|
#define RD_H GPIO.out1_w1ts.val = = (1 << (TFT_RD - 32))
|
|
#elif (TFT_RD >= 0)
|
|
#define RD_L GPIO.out_w1tc = (1 << TFT_RD)
|
|
//#define RD_L digitalWrite(TFT_WR, LOW)
|
|
#define RD_H GPIO.out_w1ts = (1 << TFT_RD)
|
|
//#define RD_H digitalWrite(TFT_WR, HIGH)
|
|
#else
|
|
#define RD_L
|
|
#define RD_H
|
|
#endif
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Macros to write commands/pixel colour data to an ILI9488 TFT
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#elif defined (ILI9488_DRIVER) // 16 bit colour converted to 3 bytes for 18 bit RGB
|
|
|
|
// Write 8 bits to TFT
|
|
#define tft_Write_8(C) spi.transfer(C)
|
|
|
|
// Convert 16 bit colour to 18 bit and write in 3 bytes
|
|
#define tft_Write_16(C) spi.transfer(((C) & 0xF800)>>8); \
|
|
spi.transfer(((C) & 0x07E0)>>3); \
|
|
spi.transfer(((C) & 0x001F)<<3)
|
|
|
|
// Convert swapped byte 16 bit colour to 18 bit and write in 3 bytes
|
|
#define tft_Write_16S(C) spi.transfer((C) & 0xF8); \
|
|
spi.transfer(((C) & 0xE000)>>11 | ((C) & 0x07)<<5); \
|
|
spi.transfer(((C) & 0x1F00)>>5)
|
|
|
|
// Write 32 bits to TFT
|
|
#define tft_Write_32(C) spi.write32(C)
|
|
|
|
// Write two concatenated 16 bit values to TFT
|
|
#define tft_Write_32C(C,D) spi.write32((C)<<16 | (D))
|
|
|
|
// Write 16 bit value twice to TFT
|
|
#define tft_Write_32D(C) spi.write32((C)<<16 | (C))
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Macros to write commands/pixel colour data to an Raspberry Pi TFT
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#elif defined (RPI_DISPLAY_TYPE)
|
|
|
|
// ESP32 low level SPI writes for 8, 16 and 32 bit values
|
|
// to avoid the function call overhead
|
|
#define TFT_WRITE_BITS(D, B) \
|
|
WRITE_PERI_REG(SPI_MOSI_DLEN_REG(SPI_PORT), B-1); \
|
|
WRITE_PERI_REG(SPI_W0_REG(SPI_PORT), D); \
|
|
SET_PERI_REG_MASK(SPI_CMD_REG(SPI_PORT), SPI_USR); \
|
|
while (READ_PERI_REG(SPI_CMD_REG(SPI_PORT))&SPI_USR);
|
|
|
|
// Write 8 bits
|
|
#define tft_Write_8(C) TFT_WRITE_BITS((C)<<8, 16)
|
|
|
|
// Write 16 bits with corrected endianess for 16 bit colours
|
|
#define tft_Write_16(C) TFT_WRITE_BITS((C)<<8 | (C)>>8, 16)
|
|
|
|
// Write 16 bits
|
|
#define tft_Write_16S(C) TFT_WRITE_BITS(C, 16)
|
|
|
|
// Write 32 bits
|
|
#define tft_Write_32(C) TFT_WRITE_BITS(C, 32)
|
|
|
|
// Write two address coordinates
|
|
#define tft_Write_32C(C,D) TFT_WRITE_BITS((C)<<24 | (C), 32); \
|
|
TFT_WRITE_BITS((D)<<24 | (D), 32)
|
|
|
|
// Write same value twice
|
|
#define tft_Write_32D(C) tft_Write_32C(C,C)
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Macros for all other SPI displays
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#else
|
|
|
|
// ESP32 low level SPI writes for 8, 16 and 32 bit values
|
|
// to avoid the function call overhead
|
|
#define TFT_WRITE_BITS(D, B) \
|
|
WRITE_PERI_REG(SPI_MOSI_DLEN_REG(SPI_PORT), B-1); \
|
|
WRITE_PERI_REG(SPI_W0_REG(SPI_PORT), D); \
|
|
SET_PERI_REG_MASK(SPI_CMD_REG(SPI_PORT), SPI_USR); \
|
|
while (READ_PERI_REG(SPI_CMD_REG(SPI_PORT))&SPI_USR);
|
|
|
|
// Write 8 bits
|
|
#define tft_Write_8(C) TFT_WRITE_BITS(C, 8)
|
|
|
|
// Write 16 bits with corrected endianess for 16 bit colours
|
|
#define tft_Write_16(C) TFT_WRITE_BITS((C)<<8 | (C)>>8, 16)
|
|
|
|
// Write 16 bits
|
|
#define tft_Write_16S(C) TFT_WRITE_BITS(C, 16)
|
|
|
|
// Write 32 bits
|
|
#define tft_Write_32(C) TFT_WRITE_BITS(C, 32)
|
|
|
|
// Write two address coordinates
|
|
#define tft_Write_32C(C,D) TFT_WRITE_BITS((uint16_t)((D)<<8 | (D)>>8)<<16 | (uint16_t)((C)<<8 | (C)>>8), 32)
|
|
|
|
// Write same value twice
|
|
#define tft_Write_32D(C) TFT_WRITE_BITS((uint16_t)((C)<<8 | (C)>>8)<<16 | (uint16_t)((C)<<8 | (C)>>8), 32)
|
|
|
|
#endif
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
// Macros to read from display using SPI or software SPI
|
|
////////////////////////////////////////////////////////////////////////////////////////
|
|
#if !defined (TFT_PARALLEL_8_BIT)
|
|
// Read from display using SPI or software SPI
|
|
// Use a SPI read transfer
|
|
#define tft_Read_8() spi.transfer(0)
|
|
#endif
|
|
|
|
// Concatenate a byte sequence A,B,C,D to CDAB, P is a uint8_t pointer
|
|
#define DAT8TO32(P) ( (uint32_t)P[0]<<8 | P[1] | P[2]<<24 | P[3]<<16 )
|
|
|
|
#endif // Header end
|